produção e purificação de enzimas quitosanolíticas produzidas … · para purificação foi...
Post on 30-Nov-2018
213 Views
Preview:
TRANSCRIPT
RENORBIO
Programa de Pós-Graduação em Biotecnologia
Produção e purificação de enzimas quitosanolíticas produzidas
por microrganismo isolado no Nordeste Brasileiro
Nathália Kelly de Araújo
NATAL/RN
2015
Tese de Doutorado apresentada ao Programa de
Pós-Graduação em Biotecnologia - Renorbio, da
Universidade Federal do Rio Grande do Norte,
como parte dos requisitos para obtenção do título
de Doutor em Biotecnologia.
NATHÁLIA KELLY DE ARAÚJO
Produção e purificação de enzimas quitosanolíticas produzidas
por microrganismo isolado no Nordeste Brasileiro
Orientador: Prof. Dr. Everaldo Silvino
dos Santos
Co-Orientador: Profa. Dra. Gorete
Ribeiro de Macedo
NATAL/RN
2015
Catalogação da Publicação na Fonte. UFRN / Biblioteca Setorial do Centro de Biociências
Araújo, Nathália Kelly.
Produção e purificação de enzimas quitosanolíticas produzidas por microrganismo isolado no Nordeste brasileiro
/ Larissa Maria da Rocha Meira. – Natal, RN, 2015.
116 f.: il.
Orientador: Prof. Dr. Everaldo Silvino dos Santos.
Coorientadora: Profa. Dra. Gorete Ribeiro de Macedo.
Tese (Doutorado) – Universidade Federal do Rio Grande do Norte. Centro de Biociências. Programa de Pós-
Graduação em Biotecnologia.
1. Cromatografia em leito expandido – Tese. 2. Bacillus Cereus. – Tese. 3. Quitosanase. – Tese. I. Santos,
Everaldo Silvino dos. II. Macedo, Gorete Ribeiro de. III. Universidade Federal do Rio Grande do Norte. IV. Título.
RN/UF/BSE-CB CDU 543.54
iv
Aos meus pais, Maria Aurea de Araújo e Otávio de Barros Neto que me enchem de inspiração e
força para que eu nunca desista da batalha da formação profissional. Que vocês estejam ao lado
de espíritos de luz!
Eu amo vocês!
v
AGRADECIMENTOS
É com muita satisfação que escrevo meus agradecimentos a todas as pessoas de extrema
importância na minha vida pessoal e profissional que de alguma forma contribuíram para a
conclusão de mais essa importante etapa em minha vida.
Primeiramente agradeço a Deus e espiritualidade por clarear minha mente e dar tranquilidade
e confiança para execução desse trabalho;
A Tiago pelo amor, incentivo e confiança durante os momentos fáceis e difíceis;
A minha Tia Zélia Barros, pelos conselhos e carinhos tão valiosos;
Aos meus irmãos, Alex, Eugênia, Paulo e Sandra pelo suporte acadêmico e sentimental;
A todos os demais familiares, pelo apoio inegável na concretização dessa jornada;
Ao professor Dr. Everaldo Silvino dos Santos, do Departamento de Engenharia Química da
Universidade Federal do Rio Grande do Norte, pela orientação e compreensão durante a
realização deste trabalho;
À professora Dra. Gorete Ribeiro de Macedo do Departamento de Engenharia Química pela co-
orientação, pela amizade, pelos conselhos, por estar sempre disposta a ensinar e esclarecer
dúvidas, e pelo crescimento profissional e pessoal proporcionados com o seu convívio. Muito
obrigada, professora, por também ter me acolhido como sua aluna de iniciação científica;
Aos professores, Sueli Rodrigues, Cristiane Assis e Matheus Pedrosa, componentes da banca de
qualificação, pela enorme contribuição para o aperfeiçoamento do trabalho;
Aos professores Eliana Kamimura, Michelle Vaz, Cristiane Assis e Matheus Pedrosa,
componentes da banca de defesa, por aceitarem participar da avaliação final desse projeto;
vi
Ao colega e técnico de laboratório Francisco Canindé de Sousa Júnior pela ajuda durante as
disciplinas e na realização de experimentos;
A Carlos Padilha, colega de laboratório, pela imensurável ajuda na elaboração de
experimentos, na interpretação de resultados e entendimento de todas as equações e números
próprios da engenharia;
Aos, também colegas e professores de laboratório, Michelle, Sérgio, Ruthinéia e Francinaldo,
pela alegria e determinação que passam as pessoas ao seu redor;
À Maria Luiza Xavier, aluna de iniciação científica que atuou nesse trabalho e tornou-se uma
grande amiga. Malu, com você aprendi mais que ensinei. Sua doçura, afeto e dedicação é algo
que não se encontra em qualquer lugar;
A todos os demais alunos de iniciação científica que dividiram e contribuíram enormemente com
esse trabalho. Em especial Humberto Arimatéia, Rafael Costa e Vanessa Pimentel;
Ao aluno de intercâmbio Jean Haury, pela troca de experiências e conhecimentos;
Aos demais colegas de laboratório pela boa convivência;
As minhas amigas e colegas de mestrado, Larissa Lira, Dayse Santos e Dayse Caroline, que me
ouviram e ajudaram durante os experimentos;
À Ana Katarina Andrade Silva pela colaboração nos experimentos de identificação dos
microrganismos;
Aos colegas de departamento e funcionários, sempre garantindo um ambiente adequado e
organizado necessários para o bem estar do nosso ambiente de trabalho;
vii
Às turmas de Farmácia e Engenharia Química pela paciência e pela oportunidade concedida
durante as aulas ministradas por mim no estágio a docência;
A coordenação de aperfeiçoamento de pessoal de nível superior (CAPES), pelo incentivo
financeiro durante meu doutorado.
viii
“É preciso provocar
sistematicamente confusão. Isso promove a
criatividade. Tudo aquilo que é contraditório
gera vida”.
Salvador Dalí
ix
RESUMO
Uma cepa produtora de quitosanase foi isolada e identificada como Bacillus cereus C-01. A
partir de extratos enzimáticos obtidos em cultivos submersos, foi efetuada a purificação da
enzima e sua caracterização bioquímica. Para purificação foi utilizada a resina da linha
Streamline DEAE e coluna de vidro (2,6 cm x 30,0 cm) acoplada a uma bomba peristáltica, em
sistema de Adsorção em Leito Expandido (ALE). As condições para a purificação da quitosanase
foram otimizadas estatisticamente através de um Planejamento Composto Central. Investigou-se
as variáveis que influenciaram significativamente nos parâmetros fator de purificação (P) e
rendimento da enzima (Y). As análises estatísticas mostraram que as melhores condições para o
máximo P foram 150 cm.h-1
(velocidade de aplicação da amostra/carga), 6,0 cm de altura do
leito fixo e 7,36 cm de altura do distribuidor. Em condições otimizadas, a enzima mostrou ligar-
se a resina na mesma medida usando caldo clarificado e não clarificado (0,32 e 0,30 U/g
adsorvente, respectivamente). Em testes qualitativos do método empregado, a fração recuperada
após a eluição exibiu 31% de rendimento e um aumento de 3,6 vezes na atividade específica em
relação ao inicial. Considerando apenas a fração eluída com NaCl 0,3 M foi possível obter um
fator de purificação de 1,75. A enzima purificada apresentou massa molecular aparente de 33
kDa, estabilidade entre as faixas de temperaturas e pH de 30 – 55 ºC e 5,5 – 8,0,
respectivamente, e máxima atividade em pH 5,5 e temperatura de 55 ºC. Os íons de Cu2+
, Fe2+
e
Zn2+
foram inibitórios para a quitosanase. Em contraste, a enzima foi significativamente ativada
por Mn2+
. Os resultados demonstraram que é possível purificar múltiplas proteínas, a partir de
um extrato bruto sem qualquer pré-tratamento, com um processo de purificação econômico e de
um único passo.
Palavras chaves: B. cereus, cromatografia em leito expandido, quitosanase.
x
ABSTRACT
A chitosanase-producing strain was isolated and identified as Bacillus cereus C-01. From
enzyme extract obtained from submerged cultures, the purification of the enzyme and
biochemical characterization were studied. For purification was used Expanded Bed Adsorption
(EBA) system with a Streamline DEAE resin and a glass column (2.6 cm x 30.0 cm) coupled to
a peristaltic pump. The conditions for the purification of chitosanase were statistically
optimized using a Central Composite Design (CCD). The variables that significantly influenced
parameters of the purification factor (P) and enzyme yield (Y) were determined. Statistical
analyses showed that the optimum conditions for maximum P were 150 cm.h-1
(load flow
velocity), 6.0 cm of settled bed height and 7.36 cm distributor height. In the optimized
conditions, the enzyme bound to resin on the same extent using clarified and unclarified broth
(0.32 and 0.30 U/g adsorbent, respectively). The optimization of purification variables resulted
in an approximately 3.66-fold increase in P compared with that observed under not optimized
conditions. The fraction recovered after the elution exhibited 31% of the yield. If considered
only the eluted fraction with 0.3 M NaCl was possible to obtain a purification factor of 1.75.
The purified enzyme showed an apparent molecular mass of 33 kDa, pH and temperature
stability between ranges of 30 – 55 °C and 5.5 – 8.0 respectively, as well as maximal activity at
pH 5.5 and temperature 55 °C. The ions Cu+2
, Fe+2
and Zn+2
showed inhibitory effect for
chitosanse. In contrast, the enzyme was significantly activated by Mn+2
.The results
demonstrated that it is possible to purify multiple proteins from crude feedstock with an
economic process and single-step purification.
Keywords: B. cereus, expanded-bed chromatography, chitosanase.
xi
LISTA DE FIGURAS
Fundamentação Teórica
Figura 1: Estruturas químicas da quitina, quitosana e COS. Fonte: Lodhi et al., 2014. .............................. 5
Figura 2: Modo de ação de uma quitosanase (a) e uma exo-β-D-glicosaminidase. Fonte: (Thadathil &
Velappan, 2014). ........................................................................................................................................... 8
Figura 3: Ciclo básico de operação da ALE. As setas indicam a direção do escoamento. Fonte:
Amersham Pharmacia Biotech. ................................................................................................................... 18
Artigo: Recovery and Purification of Chitosanase produced by Bacillus cereus using Expanded Bed
Adsorption (EBA) and Central Composite Design (CCD)
Figure 1: Response surfaces for 23 central composite designs (a) X1 – X2 (purification factor); (b) X1 – X3
(purification factor); (c) X2 – X3 (purification factor); (d) X1 – X2 (Enzyme yield); (e) X1 – X3 (Enzyme
yield); (f) X2 – X3 (Enzyme yield). ............................................................................................................. 44
Figure 2: The experimental data versus the predicted data of normalized of purification factor (a) and
enzyme yield (b). ........................................................................................................................................ 45
Figure 3: Chromatographic profile of crude extract from Bacillus cereus in streamline DEAE ion
exchange column. The column was previously equilibrated with 50 mM Tris-HCl, pH 8.5 (Buffer A) and
the sample was eluted from column with 50 mM Tris-HCl buffer, pH 8.5 containing 0.3, 0.7 and 1.0M
NaCl (Step wise). ........................................................................................................................................ 46
Artigo: Single-step purification of chitosanase from Bacillus cereus using expanded bed
chromatography
Figure 1: Time-course of cell growth, chitosanase activity and protein content. C-01 was grown
aerobically in broth medium at 30 ºC for 72 hours: (■) Chitosanase activity, (○) total protein, (●) pH and
(□) DNA content. ........................................................................................................................................ 58
Figure 2: Bed expansion height in function of superficial velocity of fluid. Unclarified (□) and clarified
culture broth (■). ......................................................................................................................................... 59
Figure 3: Effect of the presence of cells on the breakthrough curve behaviour of chitosanase into the resin
Streamline DEAE. Unclarified (□) and clarified culture broth (■). ........................................................... 60
Figure 4: Effect of expansion degree on the breakthrough curve behaviour of chitosanase into the resin
Streamline DEAE by using unclarified broth. Expansion degree of 1.2 (■), 1.5 (●) and 2.0 (▲). ............ 61
Figure 5: The elution profile of chitosanase after adsorption of broth culture on Streamline DEAE.
Content of protein (○) and enzyme activity (■). ......................................................................................... 61
xii
Figure 6: SDS-PAGE analysis of the chitosanase from B. cereus C-01. Lanes: M- molecular markers; 1-
culture supernatant; 2- load; 3- washing; 4- fraction eluted with 0.3 M NaCl; 5- fraction eluted with 0.7 M
NaCl; 6- zymogram analysis for fraction eluted with 0.3 M NaCl; 7- zymogram analysis for fraction
eluted with 0.7 M NaCl. .............................................................................................................................. 62
Figure 7: Effects of pH on the activity (■) and stability of chitosanase (●). The pH stability profile to the
enzyme was determined by measuring the residual enzyme activity at pH 6 after 24 hours of incubation in
different pH values (3.0 – 10.0) at 4 ºC. ..................................................................................................... 64
Figure 8: Effects of temperature on the activity (■) and stability of chitosanase (●). The enzymatic
samples were incubated for 60 minutes at temperature ranging from of 30 ºC to 80 ºC. ........................... 65
Figure 9: Effect of ions on chitosanase activity. The enzymatic samples were incubated at 4 ºC for 2
hours in the presence of: Mg2+,
Cu2+
, Fe2+
, Ca2+
, Zn2+
, Mn2+
and Ba2+
. ..................................................... 66
xiii
LISTA DE TABELAS
Artigo: Recovery and Purification of Chitosanase produced by Bacillus cereus using Expanded Bed
Adsorption (EBA) and Central Composite Design (CCD)
Table 1: Matrix of CCD to coded and uncoded level of independent variables. ........................................ 39
Table 2. Central Composite design variables (coded factor and levels) and effect estimates for screening
of factors affecting purification factor (P) and enzyme yield (Y). .............................................................. 41
Table 3: Analysis of variance (ANOVA) for central composite design of purification factor and enzyme
yield. ........................................................................................................................................................... 42
Artigo: Single-step purification of chitosanase from Bacillus cereus using expanded bed
chromatography
Table 1: Purification of the chitosanase from B. cereus C-01 .................................................................... 62
xiv
LISTA DE ABREVIATURAS/ SIGLAS
AE Atividade enzimática
ANOVA Análise de Variância - Analysis of variance
BSA Soro Albumina Bovina - Bovine Serum Albumin
CCD Planejamento Composto Central - Central Composite Design
COS Quitooligossacarídeos - Chitooligoshcarides
DEAE Dietilaminoetil
Df Graus de Liberdade - Degrees of freedom
DP Desvio padrão
EBA Adsorção em Leito Expandido - Expanded Bed Adsorption
Eq. Equação - Equation
GH Glicosilhidrolases - Glicosil Hidrolases
GlcN Glucosamina
GlcNAc N-acetilglucosamina
GP Grau de polimerização
kDa Quilodalton - kilodaltons
MLEE Eletroforese de enzimas multilocos
P Fator de Purificação - Purification factor
xv
PAGE Eletroforese em gel de poliacrilamida - polyacrylamide gel
electrophoresis
PCR Reação em Cadeia da Polimerase - Polymerase Chain Reaction
PFGE Eletroforese em gel de campo pulsado
Y Redimento da Enzima - Enzyme yield
rpm Rotações por minuto
RSM Metodologia de Superfície de Resposta - Response Surface Methodology
SDS Dodecil Sulfato de Sódio - Sodium dodecyl sulfate
xvi
SUMÁRIO
LISTA DE FIGURAS ................................................................................................................................ xi
LISTA DE TABELAS ............................................................................................................................. xiii
LISTA DE ABREVIATURAS/ SIGLAS ............................................................................................... xiv
1. INTRODUÇÃO ....................................................................................................................................... 2
2. FUNDAMENTAÇÃO TEÓRICA ......................................................................................................... 5
2.1. Quitina e Quitosana ........................................................................................................................... 5
2.2. Hidrólise da Quitosana ....................................................................................................................... 7
2.3. Produção de Quitosanases ................................................................................................................. 9
2.4. Bactéria Bacillus cereus .................................................................................................................... 10
2.5. Quitooligossacarídeos ...................................................................................................................... 11
2.6. Purificação de proteínas .................................................................................................................. 13
2.7. Adsorção em Leito Expandido .......................................................................................................... 15
3. REFERÊNCIAS .................................................................................................................................... 19
4. OBJETIVOS .......................................................................................................................................... 32
4.1. Objetivo geral ................................................................................................................................... 32
4.2. Objetivos específicos ........................................................................................................................ 32
5. ARTIGOS DERIVADOS DA TESE ................................................................................................... 34
Recovery and Purification of Chitosanase produced by Bacillus cereus using Expanded Bed
Adsorption (EBA) and Central Composite Design (CCD) .................................................................... 35
Abstract ...................................................................................................................................................... 35
INTRODUCTION ..................................................................................................................................... 36
MATERIALS AND METHODS ............................................................................................................. 37
Materials .................................................................................................................................................... 37
Isolation and identification of chitosanolytic bacterium ....................................................................... 37
Chitosanase production ............................................................................................................................ 37
xvii
Analytical methods .................................................................................................................................... 38
Experimental Designs ............................................................................................................................... 38
Operation of EBA ..................................................................................................................................... 39
RESULTS AND DISCUSSION ............................................................................................................... 40
Identification of chitosanase-producing strain ....................................................................................... 40
CCD and Model fitting ............................................................................................................................. 40
Analysis of variance (ANOVA) ................................................................................................................ 42
Response surface methodology (RSM) .................................................................................................... 43
Test of the model ....................................................................................................................................... 45
CONCLUSION ......................................................................................................................................... 46
REFERENCES .......................................................................................................................................... 47
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 51
Abstract ...................................................................................................................................................... 51
INTRODUCTION ..................................................................................................................................... 52
MATERIALS AND METHODS ............................................................................................................. 53
Materials .................................................................................................................................................... 53
Isolation and identification of chitosanolytic bacterium ....................................................................... 53
Chitosanase production ............................................................................................................................ 53
Hydrodynamic of the bed ......................................................................................................................... 54
Operation of EBA ..................................................................................................................................... 54
Dynamic binding capacity ........................................................................................................................ 55
Effect of pH and temperature on the enzyme activity ........................................................................... 55
Effect of various chemicals and surfactants on the enzyme activity .................................................... 56
Analytical methods .................................................................................................................................... 56
Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and zymogram analysis 56
RESULTS AND DISCUSSION ............................................................................................................... 57
xviii
Identification of chitosanase-producing strain ....................................................................................... 57
Production of chitosanase from Bacillus cereus C-01 ............................................................................ 57
Hydrodynamic of the bed ......................................................................................................................... 58
Dynamic binding capacity ........................................................................................................................ 59
Purification of chitosanase ....................................................................................................................... 61
Effect of pH and temperature .................................................................................................................. 63
Effect of various ions on enzyme activity ................................................................................................ 65
CONCLUSION ......................................................................................................................................... 66
REFERENCES .......................................................................................................................................... 67
6. CONSIDERAÇÕES FINAIS ............................................................................................................... 74
7. APÊNDICE ............................................................................................................................................ 77
Introdução 2
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
1. INTRODUÇÃO
A busca por moléculas com potencial terapêutico tem guiado a pesquisa em diversas
partes do mundo. Parte dessas pesquisas está orientada na busca de moléculas naturais de origem
vegetal, fúngica, bacteriana e animal.
O segundo polímero mais abundante na natureza é a quitina, perdendo em
biodispobilidade apenas para a celulose. A quitina é um polímero catiônico natural com estrutura
e propriedades únicas, encontrado como componente estrutural da parede celular de fungos
zigomicetos e algas clorofíceas, assim como no exoesqueleto de artrópodes (Thadathil &
Velappan, 2014).
A quitosana é a principal molécula desacetilada derivada da quitina, embora a
desacetilação não seja total. Atualmente a quitosana adquirida comercialmente é produzida de
quitina de crustáceos pela N-desacetilação usando soluções alcalinas e altas temperaturas
(Thadathil & Velappan, 2014).
Quitosana com grau de polimerização (GP) menor que 20 e massa molecular média de
3900 Da são chamados de oligômeros de quitosana, quitooligômeros ou quitooligossacarídeos
(COS) (Mourya et al., 2011). Os COS são gerados pela depolimerização da quitosana usando
hidrólise ácida, física ou degradação enzimática (Aam et al., 2010).
Recentemente, os COS têm sido objeto de interesse em termos farmacêuticos e
medicinais devido a sua não toxicidade, solubilidade, assim como os seus efeitos fisiológicos
positivos (Lodhi et al., 2014).
A hidrólise da quitosana, com o objetivo de produzir COS para uso biológico, envolve o
uso de enzimas. O método de hidrólise enzimático envolve o uso de quitosanases e outras
enzimas não específicas; este método é realizado em condições de operação brandas e permite
um controle do tamanho do produto (Lodhi et al., 2014).
Pouco tem sido descrito sobre o isolamento de microrganismos produtores de
quitosanases a partir de solos do litoral do Nordeste do Brasil, mesmo sendo esta região grande
produtora de crustáceos. Vale ressaltar que o principal componente do exoesqueleto dos
crustáceos é a quitina. A obtenção de enzimas de interesse econômico de forma mais eficiente e
com baixo custo de produção é uma das áreas de pesquisa em ascensão em biotecnologia.
Neste trabalho foram isoladas quinze cepas bacterianas. As duas que apresentaram maior
potencial para produção de quitosanases, foram identificadas por métododos moleculares:
Introdução 3
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Bacillus cereus e Serratia marcescens. Entre essas duas, a maior produção de quitosanase foi
observada no cultivo do B. cereus, assim, amostras do cultivo dessa cepa foram utilizadas em
todas as etapas subsequentes dessa tese.
A presente tese de doutorado teve como objetivo geral isolar e selecionar novos
microrganismos produtores de quitosanases, com alto potencial de hidrólise da quitosana,
produzir enzimas com atividade quitosanolítica, caracterizar tais enzimas bem como purificá-las.
A tese está dividida da seguinte forma: após uma breve introdução, desenvolvida nesse
capítulo, na qual foi contextualizada a importância da mesma, segue-se uma revisão da literatura,
na qual são apresentados os fundamentos teóricos para os capítulos seguintes, seguida dos
objetivos gerais e específicos, assim como da lista de refêrencias consultadas nessa primeira
parte do trabalho. Destaca-se que, na presente tese, a metodologia bem como os resultados e as
discussões desenvolvidas na mesma serão apresentados na forma de artigos que foram
submetidos para periódicos. Os artigos são apresentados no formato que foram enviados para os
periódicos. Em seguida, apresentam-se as considerações finais sobre o trabalho. Por fim, na
forma de apêndice, apresenta-se um modelo matemático sobre o processo de purificação
empregado nesse trabalho de doutorado. Este estudo matemático foi concebido em parceria com
um aluno do Grupo de Engenharia de Bioprocessos do Programa de Pós-graduação em
Engenharia Química. Grupo esse no qual também foi desenvolvida a presente tese.
Fundamentação Teórica 5
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
2. FUNDAMENTAÇÃO TEÓRICA
2.1. Quitina e Quitosana
Quitina é o segundo polímero mais abundante na natureza. É um polímero catiônico
natural linear de alta massa molecular composto de unidades de N-acetil-D-glicosamina unidas
por ligações β (1→4) (Aam et al., 2010), conforme estrutura apresentada na Figura 1. A quitina
apresenta propriedades únicas, sendo encontrada como componente estrutural da parede celular
de fungos zigomicetos e algas clorofíceas, assim como no exoesqueleto de artrópodes (Thadathil
& Velappan, 2014). Na sua forma natural é encontrada como microfibrilas cristalinas (Perrin et
al., 2014).
Figura 1: Estruturas químicas da quitina, quitosana e COS. Fonte: Lodhi et al., 2014.
Destaca-se que a imunogenicidade da quitina é excepcionalmente baixa, apesar da
presença de nitrogênio. Assim como a celulose, a quitina é um material altamente insolúvel e de
Fundamentação Teórica 6
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
baixa reatividade química. Sua única diferença química com a celulose, polissacarídeo mais
abundante na natureza, é a substituição de um grupo hidroxila em C-2 por um grupo amino
acetilado. Tem coloração branca e é inelástica (Lodhi et al., 2014).
A quitina existe em duas formas cristalinas polimórficas, α e β. A α-quitina consiste de
folhas fortemente empacotadas alternando entre cadeias paralelas e antiparalelas. Esta forma da
quitina é encontrada no exoesqueleto de artrópodes, insetos e na parede celular de fungos e
leveduras. A β-quitina ocorre com menos frequência na natureza do que a α-quitina, mas pode
ser extraída de gladius de lula (Aam et al., 2010).
Além da sua aplicação como matéria-prima para obtenção da quitosana e COS, a quitina
tem sido o centro de várias aplicações terapêuticas e tem se mostrado um promissor biomaterial
para engenharia de tecidos e na tecnologia de células tronco (Lodhi et al., 2014).
A partir da desacetilação química da quitina, ou por bioconversão utilizando quitina
desacetilases, obtêm-se a quitosana (Pareek et al., 2013). A quitosana é um amino polissacarídeo
composto principalmente de unidades de 2-amino-2-deoxi-D-glicose, também conhecido por
glicosamina (GlcN), ligadas linearmente por ligações glicosídicas β-1,4 com grau de acetilação
variado (Khor, 2014). A quitosana possui similaridade estrutural com glicosaminoglicanos e tem
sido amplamente investigada como um biomaterial natural para diversas aplicações biomédicas
devido a sua biocompatibilidade, biodegradabilidade, propriedades antimicrobianas e
funcionalidade (Jiang et al., 2014).
As aplicações da quitina são limitadas quando comparadas com a da quitosana. A quitina
é quimicamente inerte e insolúvel tanto em água com em ácido, enquanto a quitosana é
relativamente reativa e pode ser produzida de várias formas. A quitosana é normalmente
insolúvel em pH neutro e básico, porém torna-se solúvel em pH ácido. A solubilidade da
quitosana depende da distribuição de grupos amino livres e N-acetil. Em ácidos diluídos (pH <
6,0), os grupos amino são protonados e a molécula torna-se solúvel (Lodhi et al., 2014).
Atualmente, a quitina e quitosana comercializadas são produzidas a partir do
exoesqueleto de caranguejos e camarões, assim como da concha interna de lulas (Jung & Park,
2014). A produção da quitosana envolve desproteinização, desmineralização e desacetilação. As
características desses biopolímeros dependem do processo e condições de produção.
Características como aparência do polímero, turbidez em solução, grau de desacetilação e massa
molecular são de grande importância para aplicações biológicas e industriais (Nwe et al., 2014).
Fundamentação Teórica 7
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
2.2. Hidrólise da Quitosana
A hidrólise da quitosana é um processo similar ao que ocorre com outros polissacarídeos,
na qual a presença de determinados agentes (ácidos ou enzimas) rompe as ligações glicosídicas.
Os quitooligossacarídeos (COS), gerados a partir dessa hidrólise, apresentam variações tanto no
grau de polimerização (GP) como na sequência das unidades de glicosamina (GlcN) e N-
acetilglicosamina (GlcNAc) do oligômero gerado (Kim & Rajapakse, 2005).
Para produção em larga escala de COS, a hidrólise ácida é comumente usada para clivar
as ligações glicosídicas da quitosana. Entretanto, a hidrólise química resulta em baixa
produtividade de COS e uma grande quantidade de unidades monoméricas de D-glicosamina.
Normalmente a hidrólise química é realizada usando ácido clorídrico, nitroso, fosfórico, ou
hidrofluorídrico. Entretanto, devido à complexidade de controle do processo de reação, estes
tratamentos também resultam na formação de compostos secundários que são de difícil remoção
(Mourya et al., 2011; Lodhi et al., 2014).
Dessa forma, os COS preparados por método ácido são de difícil aplicação como material
bioativo devido à possibilidade de contaminação com componentes tóxicos. Por outro lado, a
hidrólise enzimática da quitosana tem sido proposta como método preferencial para produção de
COS bioativos (Kim & Rajapakse, 2005). Enzimas operam sob condições brandas e são
altamente específicas. Além disso, o uso de enzimas permite o controle da reação e da formação
do produto por meio do ajuste da concentração da enzima, do pH, temperatura e do tempo de
reação (Mourya et al., 2011).
A quitosana é usualmente susceptível a um grande número de enzimas, incluindo as
específicas (quitosanases) e não-específicas (carbohidrolases, proteases, lipases, entre outras)
(Kim & Rajapakse, 2005).
Pesquisas sobre quitosanases tem recebido grande atenção devido a sua ampla aplicação
em vários campos (Thadathil & Velappan, 2014). Entre essas aplicações, inclui-se a preparação
de COS bioativos (Wang et al., 2011a; de Araujo et al., 2013), de agentes de biocontrole para
aumentar a resistência de plantas contra patógenos fúngicos (Hsu et al., 2012), mediar a entrega
de gene (Almalik et al.,2013) e a bioconversão de resíduos quitinosos marinhos (Wang et al.,
2011b).
O comitê de nomenclatura de enzimas, em 2004, definiu quitosanase como enzima capaz
de realizar a endohidrólise de ligações β-1,4 entre resíduos de GlcN em uma molécula de
Fundamentação Teórica 8
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
quitosana parcialmente acetilada, a partir da extremidade redutora (Figura 2a). Posteriormente,
em 2008, o comitê criou uma segunda classe de enzima, exo-β-D-glicosaminidase que ataca a
quitosana a partir de sua terminação não redutora (Figura 2b) (Thadathil & Velappan, 2014).
Figura 2: Modo de ação de uma quitosanase (a) e uma exo-β-D-glicosaminidase. Fonte: (Thadathil &
Velappan, 2014).
Enzimas que hidrolisam as ligações glicosídicas entre açúcares são chamadas de Glicosil
Hidrolases (GH). As GH são classificadas pelo banco de dados Carbohydrate-Active enZYmes
(CAZY) o qual constantemente mantêm atualizada a lista de GH, assim como de outras enzimas
que agem sobre carboidratos. A classificação do CAZY é puramente baseada na similaridade
entre sequências de aminoácidos. Assim, várias classes de GH contêm enzimas que agem em
diferentes substratos. Enzimas com atividade quitosanolítica têm sido encontradas nas famílias
de GH 5, 7, 8, 46, 75 e 80. A GH 7 é uma família de celulases e a atividade quitosanolítica
detectada está ligada a atividade inespecífica de algumas celulases. A família GH 5 possui uma
variedade enzimas, incluindo quitosanases, celulases, liqueninases, manases e xilanases. Na
família GH 8 tem sido relatada maior atividade quitosanolítica, em alguns casos, ligado às
celulases e xilanases, em outros, realmente a quitosanases. As famílias GH 46, GH 75 e GH 80
possuem exclusivamente quitosanases. As famílias GH 75 e GH 80 possuem poucos membros e
Fundamentação Teórica 9
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
sua estrutura tridimensional ainda não foi determinada. As quitosanases mais estudadas são
aquelas pertencentes à família 46 (Aam et al., 2010).
Tem sido observado que a estrutura das pontes glicosídicas na quitosana afeta o processo
de hidrólise. Quitosanas diferencialmente desacetiladas possuem quatro diferentes tipos de
ligações glicosídicas distribuídas aleatoriamente na sua estrutura. Essas incluem ligações entre
duas unidades N-acetilglicosamina (A-A), entre uma unidade acetilada e outra desacetilada (A-
D), entre uma unidade desacetilada e outra acetilada (D-A) e entre duas unidades desacetiladas
(D-D). A especificidade da quitosanase com respeito aos quatro diferentes modos de clivar a
ligação glicosídica é determinada pela identidade das extremidades redutoras e não redutoras. A
distinção entre quitosanase e quitinase é mínima, já que ambas possuem a habilidade de degradar
uma variedade de quitosanas com diferentes graus de acetilação. Entretanto, quitinases atacam
preferencialmente polímeros com alto grau de acetilação, enquanto que, quitosanases são mais
efetivas em quitosanas com baixa N-acetilação (Mourya et al., 2011).
2.3. Produção de Quitosanases
Quitosanases são produzidas por microrganismos e plantas, onde possuem um importante
papel na nutrição e defesa.
Quitosanases extracelular de origem bacteriana já foram descridas em diversos gêneros:
Bacillus sp. (Almalik et al., 2013; Goo & Park, 2014; Liang et al., 2014), Serratia sp. (Wang et
al., 2010; Zhang et al., 2014b), Janthinobacterium sp. (Johnsen et al., 2010), Paenibacillus sp.
(de Araujo et al., 2013; Zitouni et al., 2013), Acinetobacter sp. (Wang et al., 2011b) e
Streptomyces sp.(Takasuka et al., 2014).
Com relação às quitosanases de origem fúngica, há um número menor de relatos. Cita-se,
por exemplo, a produção de quitosanases por Aspergillus sp. (Hirano et al., 2012; Beck et al.,
2014), Gongronella sp. (Zhang et al., 2013), Metarhizium anisopliae (de Assis et al., 2012) e
Trichoderma sp. (da Silva et al., 2012).
Pesquisas recentes revelam a produção de quitosanases por cianobactérias. Estas
compreendem um grupo extremamente diverso de procariontes fotossintetizantes com amplo
potencial biosintético e diversas atividades metabólicas. Em estudos utilizando Anabaena
fertilíssima foi observada a produção de uma quitosanase com potencial de uso como agente de
biocontrole (Gupta et al., 2010; Gupta et al., 2012).
Fundamentação Teórica 10
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Além dos microrganismos, algumas são produzidas por plantas (Thadathil & Velappan,
2014). Em estudo utilizando COS produzidos por hidrólise enzimática com quitosanase de broto
de bambu foi possível avaliar a atividade in vivo e in vitro desse composto (Chang et al., 2014).
Em outro estudo, também com broto de bambu, foi possível purificar e caracterizar duas
isoformas de quitosanase (Hsu et al., 2012).
2.4. Bactéria Bacillus cereus
De acordo com a taxonomia atual, o grupo Bacillus cereus inclui sete espécies
reconhecidas: Bacillus anthracis, Bacillus cereus, Bacillus thuringiensis, Bacillus
weihenstephanensis, Bacillus mycoides, Bacillus pseudomycoides e Bacillus cytotoxicus, que
compartilham um parentesco genético e bioquímico (Gillis & Mahillon, 2014). Estas espécies
foram originalmente descritas como base nos seus habitats, sua patogenicidade para mamíferos e
insetos, e suas características morfológicas e fisiológicas (Ash et al., 1991). Este grupo consiste
de espécies estreitamente relacionadas de bactérias de interesse para pesquisa devido a sua
importância na indústria e na medicina. Entretanto, ainda há dificuldade de distinguir essas
bactérias a em nível intra e inter-espécie (Punina et al., 2013).
Bacillus cereus é um comum contaminante de alimentos enquanto Bacillus thuringiensis
é capaz de produzir um bioinseticida o qual é tóxico para larvas de insetos. Na classificação
tradicional, B. thuringiensis pode ser distinguido do B. cereus pela sua capacidade de produzir
um inseticida de inclusão cristal no interior da célula durante a esporulação. Como essa
característica é frequentemente localizada no plasmídeo, o qual é transferível, quando as cepas
perdem o plasmídeo elas tornam-se indistinguíveis (Chen & Tsen, 2002).
Devido ao fato relatado acima, recentes abordagens moleculares, com alvo em genes
cromossomais, têm sido usadas para identificação específica das cepas do grupo B. cereus. A
diversidade genética da bactéria B. thuringiensis e a possibilidade de distinguí-la da bactéria B.
cereus, vem sendo estudada por diferentes métodos (Punina et al., 2013).
Para diferenciação entre B. cereus e B. thuringiensis, sondas específicas de DNA
baseadas na região variável V1 da subunidade 16S do rRNA têm sido desenhadas. Entretanto,
vários trabalhos vêm analisando sequências da subunidade 16S do rRNA das espécies deste
grupo e demonstram que elas são praticamente idênticas e dentro da variação esperada para uma
única espécie. Comparações recentes de várias cepas de B. thuringiensis e B. cereus, por
eletroforese em gel de campo pulsado (PFGE), polimorfismo de conformação de fita simples,
Fundamentação Teórica 11
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
eletroforese de enzimas multilocos (MLEE) e a diversidade de seus elementos móveis, sugerem
que estes dois Bacillus spp. devem ser considerados uma espécie (Chen & Tsen, 2002).
Além disso, o uso de outras sequências de nucleotídeos de rRNA, tais como 23S e 16S-
23S, também não permitiram estabelecer a atual relação filogenética entre B. thuringiensis e B.
cereus (Punina et al., 2013).
Dessa forma, com base em amplos estudos genômicos realizados em cepas de B. cereus e
B. thuringiensis, tem-se indicado que pode ser mais apropriado considerá-los como pertencentes
a uma espécie genérica a partir do qual vários ecótipos e patótipos surgiram (Gillis & Mahillon,
2014).
Historicamente, diversos estudos relatam a produção de quitinases e quitosanases pela
bactéria Bacillus cereus (Kurakake et al., 2000; Chang et al., 2007; Liang et al., 2012; Liang et
al., 2013; Goo & Park, 2014; Liang et al., 2014; Seo et al., 2014).
2.5. Quitooligossacarídeos
A quitosana é suscetível de hidrólise (degradação hidrolítica) devido à presença de pontes
glicosídica na molécula; essas ligações são bastante instáveis quando tratadas com agentes
hidrolisantes, como por exemplo, soluções aquosas de ácidos. Quitosana com Grau de
Polimerização (GP) inferior a 20 e com massa molecular média menor do que 3900 Da são
chamados de oligômeros de quitosana, quitooligômeros ou quitooligosacarídeos (COS) (Mourya
et al., 2011). Os COS não são solúveis em acetona, butanol, etanol, acetato de etila, propanol e
piridina mas são totalmente solúveis em água e parcialmente solúvel em metanol e dimetil
sulfóxido. Oligômeros com GP entre 2-4 são solúveis em metanol, mas oligômeros com GP
maior que 5 são menos solúveis (Mourya et al., 2011).
Diferentemente da maioria dos polissacarídeos, a quitosana e os COS têm cargas
positivas, o que lhes permite se ligar fortemente a superfícies negativamente carregadas; esta
propriedade é responsável por muitas atividades biológicas já descritas para estas moléculas. No
entanto, é importante mencionar que COS com estruturas diferentes apresentam diferentes
atividades biológicas, e nem todas as atividades biológicas são encontradas em um dado COS.
Cada tipo especial de COS bioativo é desenvolvido através da modificação química e/ou
hidrólise enzimática para potencial aplicação farmacêutica e médica (Zhang et al., 2010).
Os COS têm sido objeto de crescente atenção em termos de aplicações medicinais e
farmacêuticas, devido a sua alta solubilidade e não toxicidade bem como aos seus efeitos
Fundamentação Teórica 12
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
fisiológicos positivos. Recentes avanços têm lançado luz sobre os benefícios do COS à saúde,
incluindo a redução do colesterol no sangue e da pressão arterial elevada, efeitos de proteção
contra infecções, controle da artrite, melhora da absorção de cálcio e propriedades antitumorais
(Lodhi et al., 2014).
No início do ano 1970, foi relatada a primeira atividade biológica, antitumoral, dos COS.
Essa atividade foi inicialmente sugerida como induzida pela propriedade catiônica exercida por
grupos amino dos COS. Posteriormente, foi aceito que a massa molecular também possui papel
majoritário para a atividade antitumoral (Lodhi et al., 2014). Tem sido demonstrada a ação
antitumoral tanto com uso de células tumorais, por exemplo, HepG2, HeLa (de Assis et al.,
2012) e HL-60 (Kim et al., 2012), como com uso de modelos animais. Estudos in vivo com
portadores de câncer de pulmão constatou que a administração oral de COS pode regular a
função imune, reduzir os efeitos negativos da radioterapia sobre a imunidade e ter um bom efeito
antitumoral adjuvante (Ma et al., 2015). Também foi demonstrado que administração oral de
COS em ratos portadores de tumor de cólon suprime o crescimento do tumor, através da indução
de apoptose e a estimulação do sistema imunitário, o que sugere que os COS são potencialmente
um alimento funcional (Masuda et al., 2014).
Pesquisas também tem evidenciado diretamente a ação antioxidante dos COS. Destaca-se
que foi relatada a inibição do estresse oxidativo induzido por etanol (Luo et al., 2014b), o
sequestro de radicais DPPH (Eom et al., 2012; de Araujo et al., 2013) e superóxido (de Assis et
al., 2012; Li et al., 2013). A inibição da oxidação celular, em células sob estresse oxidativo,
também já foi descrita em diversos trabalhos, por exemplo, com macrófagos RAW264.7 (Ngo et
al., 2011), eritrócitos (Fernandes et al., 2010, Zhang et al., 2014a), células pancreáticas MIN6
(Lu et al., 2012) e de fígado (Trinh et al., 2014).
Também se destacam os efeitos: imunoestimulante (Zhang et al., 2014c), antibacteriana
(Wu et al., 2013; Younes et al., 2014), prebiótica (Kong et al., 2014), antidiabética (Katiyar et
al., 2011), supressão de metástase (Luo et al., 2014a), ativação da resistência de plantas contra
insetos e ataques de patógenos (Zhang et al., 2011), antifúngica (Suma & Podile, 2013; Younes
et al., 2014), anti-inflamatória (Azuma et al., 2015), antiviral (Artan et al., 2010), prevenção da
adesão bacteriana em células humanas (Rhoades et al., 2006) e uso como vetor para entrega de
genes (Issa et al., 2006; Csaba et al., 2009).
Fundamentação Teórica 13
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
2.6. Purificação de proteínas
Após a produção de biomoléculas de interesse industrial, farmacêutico e/ou medicinal
utiliza-se operações unitárias (Downstream processing) que possam garantir o grau de pureza
desejado do material, que dependerá de sua aplicação.
Pesquisadores têm purificado e caracterizado com sucesso um grande número de
proteínas de uma variedade de microrganismos usando diferentes técnicas. A partir desses
passos são obtidas diferentes informações, tais como atividade específica, rendimento, ponto
isoelétrico, massa molecular, Km, Vmax, pH e temperatura ótimas. Várias estratégias envolvendo
passos individuais ou multi-passos normalmente são empregadas (Sooch et al., 2014).
A eficiência do Downstream processing é influenciada pela concentração de proteínas,
pela complexidade do extrato bruto e pelo grau de pureza requerido. Esse processo pode ser
dividido em duas fases: recuperação primária e purificação (Wilken & Nikolov, 2012).
O objetivo da recuperação primária é maximizar o título do produto e o rendimento no
extrato ou homogeneizado celular, reduzir o volume e preparar uma amostra clarificada para a
purificação. Processos downstream para sistemas baseados em biorreatores iniciam-se com a
coleta da biomassa por centrifugação, filtração com membranas, ou por bombeamento do meio
líquido para fora do biorreator. Para proteínas intracelulares é necessário o rompimento da
célula; enquanto que para proteínas extracelulares, o meio de cultura é tipicamente concentrado,
clarificado e condicionado antes de serem submetidas a processos cromatográficos. Algumas das
operações unitárias de recuperação primária, tais como a centrifugação, filtração de fluxo
cruzado e filtração frontal, são multifuncionais, e as suas estratégias de aplicações são definidas
pela composição e propriedades do extrato, tamanho das partículas e a estabilidade do produto
(Wilken & Nikolov, 2012).
Proteínas podem ser purificadas na sua forma ativa com base em características tais como
solubilidade, tamanho, carga e afinidade específica de ligação. A etapa de purificação
usualmente inicia-se com o passo de concentração de proteína (por exemplo, precipitação com
sulfato de amônio ou solventes ou polietileno glicol) e remoção de impurezas que poderão afetar
o rendimento, qualidade e/ou a eficiência da purificação (Thadathil & Velappan, 2014). Para
aplicações que exigem alto grau de pureza (uso em terapias e diagnóstico), etapas adicionais de
purificação são necessárias, principalmente para remover impurezas residuais e assegurar a
qualidade do produto (Wilken & Nikolov, 2012).
Fundamentação Teórica 14
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Para purificação de quitosanases e quitinases, aplicam-se diferentes técnicas
cromatográficas tais como filtração em gel (Oh et al., 2011), troca iônica (Jiang et al., 2012,
Nguyen et al., 2014), combinação das duas técnicas (Wang et al., 2008; Wang & Yeh, 2008) e
afinidade (Yang et al., 2007). Para quitosanases produzidas pelo Bacillus cereus tem-se
empregado principalmente combinação de gel filtração com troca iônica (Liang et al., 2012;
Liang et al., 2014) e somente gel filtração (Goo & Park, 2014).
A gel filtração é um tipo de cromatografia baseada no tamanho das partículas. A amostra
é aplicada no topo de uma coluna preenchida com um polímero poroso e insolúvel, mas
altamente hidratado, normalmente dextrana ou agarose ou poliacrilamida. Sephadex, Sepharose e
Bio-gel são as preparações comerciais mais usadas nessas resinas, as quais tipicamente possuem
grânulos com 100µm de diâmetro. Pequenas moléculas podem entrar nos poros dessa resina, mas
as grandes não. O resultado é que as moléculas pequenas são distribuídas na solução aquosa,
tanto no interior dos grânulos da resina como entre eles, enquanto que as moléculas grandes
estão localizadas apenas na solução entre os grânulos. As moléculas grandes fluem mais
rapidamente através da coluna e saem primeiro porque um volume menor é suficiente para eluí-
las. As moléculas que são de um tamanho médio, ocasionalmente entram no interior de um
grânulo e irão fluir em uma velocidade intermediária. Enquanto as moléculas pequenas, as quais
tomam um caminho tortuoso e mais longo, serão eluídas por último (Berg et al., 2002).
Na cromatografia de troca iônica, as proteínas são separadas de acordo com a carga
líquida que a mesma possui. Se uma proteína exibe carga positiva em pH 7,0, normalmente ela
irá se ligar a uma resina contendo contra-íons positivos, deslocando-os. Uma proteína
positivamente carregada ligada a uma resina pode então ser eluída aumentando-se a concentração
de cloreto de sódio ou outro sal no tampão de eluição, os íons sódio, agora com uma maior força
iônica, competem com a proteína deslocando-a. As proteínas que têm uma baixa densidade de
carga positiva líquida tenderão a ser eluídas em primeiro lugar, seguida daquelas que têm uma
densidade de carga mais elevada (Berg et al., 2002; Nelson & Cox, 2006).
Em um processo de purificação, diversas variáveis devem ser estudadas. Tratando-se de
bioprodutos, especificamente enzimas, o desempenho da técnica de purificação pode ser
evidenciado pelas variáveis redimento da atividade enzimática e fator de purificação (Padilha,
2013).
Fundamentação Teórica 15
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
O redimento da atividade enzimática é a relação entre a atividade enzimática do material
purificado e a atividade do extrato bruto, a qual pode ser expressa em percentual (Padilha, 2013):
𝑹𝒆𝒏𝒅𝒊𝒎𝒆𝒏𝒕𝒐 (%) =𝑨𝒕𝒊𝒗𝒊𝒅𝒂𝒅𝒆 𝒆𝒏𝒛𝒊𝒎á𝒕𝒊𝒄𝒂 𝒅𝒐 𝒎𝒂𝒕𝒆𝒓𝒊𝒂𝒍 𝒑𝒖𝒓𝒊𝒇𝒊𝒄𝒂𝒅𝒐
𝑨𝒕𝒊𝒗𝒊𝒅𝒂𝒅𝒆 𝒆𝒏𝒛𝒊𝒎á𝒕𝒊𝒄𝒂 𝒏𝒐 𝒎𝒂𝒕𝒆𝒓𝒊𝒂𝒍 𝒃𝒓𝒖𝒕𝒐 𝒙 𝟏𝟎𝟎 Eq.1
O fator de purificação expressa o quão seletivo é o processo de purificação, relacionando
as atividades específicas do material purificado e do seu estado inicial (Padilha, 2013):
𝑭𝒂𝒕𝒐𝒓 𝒅𝒆 𝒑𝒖𝒓𝒊𝒇𝒊𝒄𝒂çã𝒐 = 𝑨𝒕𝒊𝒗𝒊𝒅𝒂𝒅𝒆 𝒆𝒔𝒑𝒆𝒄í𝒇𝒊𝒄𝒂 𝒏𝒐 𝒎𝒂𝒕𝒆𝒓𝒊𝒂𝒍 𝒑𝒖𝒓𝒊𝒇𝒊𝒄𝒂𝒅𝒐
𝑨𝒕𝒊𝒗𝒊𝒅𝒂𝒅𝒆 𝒆𝒔𝒑𝒆𝒄í𝒇𝒊𝒄𝒂 𝒏𝒐 𝒎𝒂𝒕𝒆𝒓𝒊𝒂𝒍 𝒃𝒓𝒖𝒕𝒐 Eq.2
2.7. Adsorção em Leito Expandido
A viabilidade econômica de um bioprocesso está diretamente ligada ao número e
eficiência das etapas necessárias durante a purificação, a fim de alcançar as especificações dos
produtos solicitados. Adsorção em Leito Expandido (ALE) é um processo integrado que
combina a separação sólido-líquido e a recuperação do produto numa única operação unitária.
Esta abordagem sugere um aumento do rendimento global, menor necessidade de investimentos
de capital e de consumo e, sobretudo, uma redução do tempo de processo. O sucesso de um
processo de integração é, no entanto, intimamente ligada a uma compreensão detalhada dos
princípios bioquímicos envolvidos e as limitações decorrentes da complexidade de matéria-prima
(Hubbuch et al., 2005).
A ALE permite que proteínas sejam recuperadas diretamente a partir de cultura de
microrganismos ou de células, sem a necessidade de remoção prévia de sólidos suspensos. O
desempenho geral da ALE é comparável à de um leito empacotado devido à redução da mistura
das partículas de adsorvente na coluna. No entanto, as condições ideais de operação são mais
restritas devido à dependência da expansão do leito e a densidade requerida das partículas de
adsorvente, bem como a viscosidade e a densidade da matéria-prima. A composição da matéria-
prima pode se tornar mais uma restrição limitante devido às interações das partículas adsorventes
com superfície das células, DNA e outras substâncias, levando a sua agregação e,
consequentemente, a instabilidades do leito e formação de canais preferenciais. Apesar destas
dificuldades, a ALE tem encontrado aplicações generalizadas na purificação em grande escala de
proteínas de células de mamíferos e microbianas (Anspach et al., 1999).
O estudo e uso de leito fluidizado como ferramenta cromatográfica passou a ser utilizado
com maior efetividade a partir da década de 90 (Draeger & Chase, 1990). A partir da introdução
Fundamentação Teórica 16
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
de novos tipos de adsorventes destinados a operação em leito expandido, linha streamline
produzida pelo grupo Amersham Phamarcia Biotech atual G&E, foi possível uma maior
estabilidade do leito e um aumento na faixa de velocidade de operação (100-300 cm.h-1
)
(Padilha, 2013).
A matriz do adsorvente deve mostrar características de fluidização adequadas. Em
particular, o leito deve ter a capacidade de expansão requerida (cerca de duas a três vezes a altura
do leito fixo) quando aplicada uma velocidade de fluxo adequada. Existe uma estreita relação
entre a altura do leito expandido e a velocidade de fluxo, a qual depende criticamente das
propriedades físicas do adsorvente e da alimentação utilizada. Além disso, as partículas do
adsorvente devem possuir faixas de diâmetro que sejam adequadas para geração de uma
expansão estável (Chase, 1994).
O comportamento fluidinâmico do leito expandido engloba três características
primordiais, o regime de escoamento, o grau de mistura e a possibilidade de existência de
camada estagnada entre o fluido e o adsorvente. Pode-se ressaltar que a Adsorção em Leito
Expandido se baseia na manutenção da fluidização estável (mais semelhante ao escoamento
plug-flow), estabelecendo um balanço entre as propriedades fluidodinâmicas entre o leito
fluidizado e as propriedades cromatográficas do leito fixo (Padilha, 2013).
Durante a operação de uma coluna em leito expandido para purificação de bioprodutos é
essencial o conhecimento do comportamento leito em função das propriedades das partículas do
adsorvente e da solução de alimentação. Esta caracterização é baseada no mensuramento do grau
de expansão em função da velocidade e viscosidade do fluido, na presença de contaminantes
como células microbianas e na distribuição das partículas do adsorvente (Moraes et al., 2013).
Uma das formas de conhecer o comportamento de um leito expandido e o seu regime de
escoamento, em função das propriedades físicas das partículas e do fluido, é por meio da
equação de Richardson-Zaki (Richardson & Zaki, 1954). Pela teoria, a velocidade terminal de
uma partícula esférica (Ut) é influenciada pelo movimento das outras (interferência
populacional), conforme Equação 3 (Padilha, 2013):
𝒖 = 𝒖𝑻 . 𝜺𝒏 Eq.3
Sendo u a velocidade superficial, ε refere-se a porosidade do leito, uT é a velocidade terminal de
uma partícula única e n o índice de expansão do leito.
Fundamentação Teórica 17
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Esse modelo descreve a influência da população sobre a velocidade terminal individual,
sendo fundamental para avaliar a expansão do leito quando este alcança o equilíbrio (Padilha,
2013). Os parâmetros uT e n são determinados pela linearização da Equação 3:
𝑙𝑛 𝑢 = 𝑙𝑛 𝑢𝑇 + 𝑛 . 𝑙𝑛 𝜀 Eq.4
A porosidade do leito pode ser estimada em função da altura total de expansão do leito
(Moraes et al., 2013):
𝜺 = 𝟏 − (𝟏 − 𝜺𝟎).𝑯𝟎
𝑯 Eq. 5
Onde ε0 e H0 são a porosidade e altura do leito sedimentado, respectivamente. Admite-se que ε0
tem valor igual a 0,4 (Moraes et al., 2013).
Outra informação importante a ser aferida sobre o sistema é a capacidade dinâmica de
ligação. Esta normalmente é determinada quando a concentração de proteína ou a atividade
enzimática no efluente da coluna alcança 10% da concentração ou atividade inicial (C/C0=0,1 ou
U/U0=0,1), assim há redução de perda da molécula alvo no escoamento. A capacidade dinâmica
de ligação (QB), definida como concentração de proteína ou unidade de enzima adsorvida por
massa do adsorvente, pode ser calculada de acordo com a Equação 6:
𝑸𝑩 =𝑪𝟎(𝑽𝒇−𝑽𝒎) ∫ 𝑪𝒅𝑽
𝑽𝒇𝑽𝒎
𝒎𝒂𝒅𝒔 Eq. 6
Onde C0 é a concentração de proteína (mg.mL-1
) ou a atividade enzimática inicial (U.mL-1
), Vf é
o volume final de solução de alimentação, Vm é o volume a 10% de ruptura (mL) e mads refere-se
a massa de adsorvente (g).
O ciclo de operação básico da ALE é composto pelas etapas de equilíbrio, aplicação da
amostra, lavagem, eluição e posterior limpeza da resina (Figura 3). As estratégias de otimização
de cada etapa são, em geral, semelhantes às adotadas em um processo de leito convencional
(Chase, 1994).
Fundamentação Teórica 18
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figura 3: Ciclo básico de operação da ALE. As setas indicam a direção do escoamento. Fonte: Amersham
Pharmacia Biotech.
O processo de ALE também é operado de forma muito semelhante ao processo
empacotado. A principal diferença é a direção do fluxo do líquido. Uma velocidade de fluxo
mais baixa pode ser usada se a viscosidade da matéria-prima for muito alta. Isto pode prevenir
uma expansão muito elevada (Hjorth, 1997).
No início do protocolo de purificação, o adsorvente sedimentado necessita ser convertido
em um leito expandido e estável antes da aplicação da alimentação contendo material
particulado. Para isso uma solução tampão é aplicada e esta flui através do leito, inicialmente sob
um baixo fluxo e sendo gradualmente elevado até que se atinja uma altura duas vezes maior que
a inicial. Feito isso a amostra pode ser aplicada no sistema. Entretanto, as propriedades físicas da
alimentação podem ser diferentes daquelas do tampão usado na expansão inicial do leito. Como
consequência, se o fluxo não for reduzido, a extensão da expansão do leito poderá aumentar.
Após aplicação da amostra, inicia-se a etapa de lavagem (Chase, 1994).
A etapa de lavagem de um processo de leito expandido tem a dupla função de remoção de
matéria-prima mantida dentro dos espaços vazios inter e intrapartícula do adsorvente e, em
alguns casos, remoção de material fracamente adsorvido (Chase, 1994).
Depois do material não ligado ter sido lavado da resina (etapa de lavagem), o fluxo é
interrompido e deixa-se a resina sedimentar. A etapa de eluição geralmente é realizada em modo
empacotado e a uma velocidade reduzida, normalmente 100 cm.h-1
para manter baixo o volume
da fração eluída. A eluição também pode ser realizada com o leito expandido, mas tem sido
descrito um aumento de 40% no volume da fração eluida (Hjorth, 1997).
Fundamentação Teórica 19
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Um importante estágio na operação de um leito expandido é o procedimento de limpeza e
regeneração da resina. Este procedimento é realizado para manter a funcionalidade do
adsorvente, garantir que todas as impurezas tenham sido removidas e evitar a passagem de
contaminante entre amostras de resina. A maioria dos procedimentos de limpeza inclui a
utilização de hidróxido de sódio em concentrações de 0,5 a 1M. Este tratamento deve ser
realizado durante um período controlado de tempo (3-4 horas), para permitir que os
contaminantes sejam removidos. O hidróxido de sódio é geralmente combinado com outras
soluções, tais como 10% de ácido acético ou solventes orgânicos como etanol 20% (Hjorth,
1997).
Nos últimos anos, a ALE tem sido empregada na purificação das mais diversas
biomoléculas, das quais pode-se citar a purificação de ácido salvinólico e alcalóides (Li et al.,
2014), lactoferrina e imunoglobulina G (Du et al., 2014), ficocianina C (Moraes et al., 2013),
antígeno recombinante da Hepatite B (Ng et al., 2012) e β-galactosidade (Boeris et al., 2012).
Conforme relatado anteriormente, é comum o uso de resinas de troca iônica em leito
empacotado para purificação de quitosanases, recentemente também foi relatado o uso de resinas
de troca iônica, linha Streamline, para purificação de duas quitosanases produzidas pelo fungo
Metarhizium anisopliae (de Santana et al., 2014).
Tendo em vista o exposto, no presente estudo foi adotada a estratégia de planejamento
experimental com a realização de um Planejamento Composto Central para o estudo de uma
estratégia de purificação de uma quitosanase utilizando ALE.
3. REFERÊNCIAS
Aam, B. B.; Heggset, E. B.; Norberg, A. L.; Sorlie, M.; Varum, K. M.; Eijsink, V. G. Production
of chitooligosaccharides and their potential applications in medicine. Marine Drugs 8(5): 1482-
1517, 2010.
Almalik, A.; Day, P. J.; Tirelli, N. "HA-coated chitosan nanoparticles for CD44-mediated
nucleic acid delivery." Macromolecular Bioscience 13(12): 1671-1680,2013.
Fundamentação Teórica 20
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Amersham Pharmacia Biotech. Expanded bed adsorption handbook. Disponível em:
http://wolfson.huji.ac.il/purification/PDF/Expanded_Bed_Absorption/PHARMACIA_IntrodEB
A.pdf Acesso em abril de 2015.
Anspach, F. B.; Curbelo, D.; Hartmann, R.; Garke, G.; Deckwer, W. D. "Expanded-bed
chromatography in primary protein purification." Journal of Chromatography A 865(1-2): 129-
144,1999.
Artan, M.; Karadeniz, F.; Karagozlu, M.Z.; Kim, M. M.; Kim, S. K. "Anti-HIV-1 activity of low
molecular weight sulfated chitooligosaccharides." Carbohydrate Research 345(5): 656-662,2010.
Ash, C.; Farrow, J. A.; Dorsch, M.; Stackebrandt, E.; Collins, M. D. "Comparative analysis of
Bacillus anthracis, Bacillus cereus, and related species on the basis of reverse transcriptase
sequencing of 16S rRNA." International Journal of Systematic Bacteriology 41(3): 343-
346,1991.
Azuma, K.; Osaki, T.; Kurozumi, S.; Kiyose, M.; Tsuka, T.; Murahata, Y.; Imagawa, T.; Itoh,
N.; Minami, S.; Sato, K.; Okamoto, Y. "Anti-inflammatory effects of orally administered
glucosamine oligomer in an experimental model of inflammatory bowel disease." Carbohydrate
Polymers 115(0): 448-456, 2015.
Beck, J.; Broniszewska, M.; Schwienbacher, M.; Ebel, F. "Characterization of the Aspergillus
fumigatus chitosanase CsnB and evaluation of its potential use in serological diagnostics."
International Journal of Medical Microbiology 304(5-6): 696-702, 2014.
Berg, J. M.; Tymoczko, J. L.; Stryer, L. Biochemistry, Fifth Edition. 5 ed. Nova York: W.H.
Freeman, 2002, 1050p.
Boeris, V.; Balce, I.; Vennapusa, R. R.; Rodríguez, M. A.; Picó, G.; Lahore, M. F. "Production,
recovery and purification of a recombinant β-galactosidase by expanded bed anion exchange
adsorption." Journal of Chromatography B 900(0): 32-37, 2012.
Fundamentação Teórica 21
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Chang, W. T.; Chen, Y. C.; Jao, C. L. "Antifungal activity and enhancement of plant growth by
Bacillus cereus grown on shellfish chitin wastes." Bioresource Technology 98(6): 1224-1230,
2007.
Chang, Y.-M.; Lee, Y. -J; Liao, J. -W.; Jhan, J.-K.; Chang, C.-T.; Chung, Y.-C. "In vitro and in
vivo safety evaluation of low molecular weight chitosans prepared by hydrolyzing crab shell
chitosans with bamboo shoots chitosanase." Food and Chemical Toxicology 71(0): 10-16, 2014.
Chase, A.H. “Purification of proteins by adsorption chromatography in expanded beds”. Trends
Biotechnology 12(8):296-303, 1994.
Chen, M. L.; Tsen, H. Y. "Discrimination of Bacillus cereus and Bacillus thuringiensis with 16S
rRNA and gyrB gene based PCR primers and sequencing of their annealing sites." Journal of
Applied Microbiology 92(5): 912-919, 2002.
Csaba, N.; Köping-Höggård, M.; Alonso, M. J. "Ionically crosslinked chitosan/tripolyphosphate
nanoparticles for oligonucleotide and plasmid DNA delivery." International Journal of
Pharmaceutics 382(1–2): 205-214, 2009.
da Silva, L. C.; Honorato, T. L.; Cavalcante, R. S.; Franco, T. T.; Rodrigues, S. "Effect of pH
and Temperature on Enzyme Activity of Chitosanase Produced Under Solid Stated Fermentation
by Trichoderma spp." Indian Journal of Microbiology 52(1): 60-65, 2012.
de Araujo, N. K.; de Assis, C. F.; Dos Santos, E. S.;de Macedo, G. R.; de Farias, L. F.; Arimateia
Jr., H.; de Freitas Fernandes Pedrosa, M.; Pagnoncelli, M. G. "Production of enzymes by
Paenibacillus chitinolyticus and Paenibacillus ehimensis to obtain chitooligosaccharides."
Applied Biochemistry Biotechnology 170(2): 292-300, 2013.
de Assis, C. F.; Costa, L. S.; Melo-Silveira, R. F.; Oliveira, R. M.; Pagnoncelli, M. G.; Rocha, H.
A.; de Macedo, G. R.; Santos, E. S. "Chitooligosaccharides antagonize the cytotoxic effect of
glucosamine." World Journal of Microbiology and Biotechnology 28(3): 1097-1105, 2012.
Fundamentação Teórica 22
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
de Santana, S.; da Silva Filho, R.; dos Santos Cavalcanti, J.; de Oliveira, J.; de Macedo, G.;
Padilha, F.; dos Santos, E. "Modeling and simulation of breakthrough curves during purification
of two chitosanases from Metarhizium anisopliae using ion-exchange with expanded bed
adsorption chromatography." Korean Journal of Chemical Engineering 31(4): 684-691, 2014.
Draeger, N. M.; Chase, H. A. "Modelling of protein adsorption in liquid fluidized beds". In: Pyle
DL (ed). Separations for biotechnology 2. Dorking: Elsevier, 1990, 325-334.
Du, Q.-Y.; Lin, D.-Q; Zhang, Q.-L; Yao, S.-J. "An integrated expanded bed adsorption process
for lactoferrin and immunoglobulin G purification from crude sweet whey." Journal of
Chromatography B 947–948(0): 201-207, 2014.
Eom, T. K.; Senevirathne, M.; Kim, S. K. "Synthesis of phenolic acid conjugated
chitooligosaccharides and evaluation of their antioxidant activity." Environmental Toxicology
and Pharmacology 34(2): 519-527, 2012.
Fernandes, J. C.; Eaton, P.; Nascimento, H.; Gião, M.S; Ramos, O. S.; Belo, L.; Santos-Silva, A.;
Pintado, M. E.; Malcata, F. X.. "Antioxidant activity of chitooligosaccharides upon two
biological systems: Erythrocytes and bacteriophages." Carbohydrate Polymers 79(4): 1101-1106,
2010.
Gillis, A.; Mahillon, J. "Phages preying on Bacillus anthracis, Bacillus cereus, and Bacillus
thuringiensis: past, present and future." Viruses 6(7): 2623-2672, 2014.
Goo, B. G.; Park, J. K. "Characterization of an alkalophilic extracellular chitosanase from
Bacillus cereus GU-02." Journal of Bioscience and Bioengineering 117(6): 684-689, 2014.
Gupta, V.; Prasanna, R.; Natarajan, C.; Srivastava, A. K.; Sharma, J. "Identification,
characterization, and regulation of a novel antifungal chitosanase gene (cho) in Anabaena spp."
Applied and Environmental Microbiology 76(9): 2769-2777, 2010.
Fundamentação Teórica 23
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Gupta, V.; Prasanna, R.; Srivastava, A.; Sharma, J. "Purification and characterization of a novel
antifungal endo-type chitosanase from Anabaena fertilissima." Annals of Microbiology 62(3):
1089-1098, 2012.
Hirano, K.; Arayaveerasid, S.; Seki, K.; Adams, D. J.; Mitsutomi, M. "Characterization of a
chitosanase from Aspergillus fumigatus ATCC13073." Bioscience Biotechnology and
Biochemistry 76(8): 1523-1528, 2012.
Hjorth, R. “Expanded-bed adsorption in industrial bioprocessing: recent developments”. Trends
Biotechnology 15(6):230-235, 1997.
Hsu, S. K.; Chung, Y. C.; Chang, C. T.; Sung, H. Y. "Purification and characterization of two
chitosanase isoforms from the sheaths of bamboo shoots." Journal of Agricultural and Food
Chemistry 60(2): 649-657, 2012.
Hubbuch, J.; Thommes, J.; Kula, M. R. "Biochemical engineering aspects of expanded bed
adsorption." Advances in Biochemical Engineering/Biotechnology 92: 101-123, 2005.
Issa, M. M.; Köping-Höggård, M.; Tømmeraas, K.; Vårum, K. M.; Christensen, B. E.; Strand, S.
P.; Artursson, P. "Targeted gene delivery with trisaccharide-substituted chitosan oligomers in
vitro and after lung administration in vivo." Journal of Controlled Release 115(1): 103-112,
2006.
Jiang, T.; James, R.; Kumbar, S. G.; Laurencin, C. T. "Chapter 5 - Chitosan as a Biomaterial:
Structure, Properties, and Applications in Tissue Engineering and Drug Delivery". Natural and
Synthetic Biomedical Polymers. S. G. Kumbar, C. T. Laurencin and M. Deng. Oxford, Elsevier:
91-113, 2014.
Jiang, X.; Chen, D.; Chen, L.; Yang, G.; Zou, S. "Purification, characterization, and action mode
of a chitosanase from Streptomyces roseolus induced by chitin." Carbohydrate Research 355: 40-
44, 2012.
Fundamentação Teórica 24
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Johnsen, M. G.; Hansen, O. C.; Stougaard, P. "Isolation, characterization and heterologous
expression of a novel chitosanase from Janthinobacterium sp. strain 4239." Microbial Cell
Factories 9: 5, 2010.
Jung, W. J.; Park, R. D. "Bioproduction of chitooligosaccharides: present and perspectives."
Marine Drugs 2 (11):5328-5356, 2014.
Katiyar, D.; Singh, B.; Lall, A. M.; Haldar, C. "Efficacy of chitooligosaccharides for the
management of diabetes in alloxan induced mice: A correlative study with antihyperlipidemic
and antioxidative activity." European Journal of Pharmaceutical Sciences 44(4): 534-543, 2011.
Khor, E. "3 - Traditional Chitin and Chitosan Biomaterials Research". Chitin (Second Edition).
E. Khor. Oxford, Elsevier: 29-50, 2014.
Kim, E. K.; Je, J. Y.; Lee, S. J.; Kim, Y. S.; Hwang, J. W.; Sung, S. H.; Moon, S. H.; Jeon, B. T.;
Kim, S. K.; Jeon, Y. J.; Park, P. J. "Chitooligosaccharides induce apoptosis in human myeloid
leukemia HL-60 cells." Bioorganic & Medicinal Chemistry Letters 22(19): 6136-6138, 2012.
Kim, S.-K.; Rajapakse, N. "Enzymatic production and biological activities of chitosan
oligosaccharides (COS): A review." Carbohydrate Polymers 62(4): 357-368, 2005.
Kong, X. F.; Zhou, X. L.; Lian, G. Q.; Blachier, F.; Liu, G.; Tan, B. E.; Nyachoti, C. M.; Yin, Y.
L. "Dietary supplementation with chitooligosaccharides alters gut microbiota and modifies
intestinal luminal metabolites in weaned Huanjiang mini-piglets." Livestock Science 160(0): 97-
101, 2014.
Kurakake, M.; Yo-u, S.; Nakagawa, K.; Sugihara, M.; Komaki, T. "Properties of chitosanase
from Bacillus cereus S1." Current Microbiology 40(1): 6-9, 2000.
Li, K.; Liu, S.; Xing, R.; Qin, Y.; Li, P. "Preparation, characterization and antioxidant activity of
two partially N-acetylated chitotrioses." Carbohydrate Polymers 92(2): 1730-1736, 2013.
Fundamentação Teórica 25
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Li, Y.; Wang, N.; Zhang, M.; Ito, Y.; Zhang, H.; Wang, Y.; Guo, X.; Hu, P. "Development of a
Method to Extract and Purify Target Compounds from Medicinal Plants in a Single Step: Online
Hyphenation of Expanded Bed Adsorption Chromatography and Countercurrent
Chromatography." Analytical Chemistry 86(7): 3373-3379, 2014.
Liang, T. W.; Chen, Y. Y.; Pan, P. S.; Wang, S. L. "Purification of chitinase/chitosanase from
Bacillus cereus and discovery of an enzyme inhibitor." International Journal of Biological
Macromolecules 63: 8-14, 2014.
Liang, T. W.; Hsieh, J. L.; Wang, S. L. "Production and purification of a protease, a chitosanase,
and chitin oligosaccharides by Bacillus cereus TKU022 fermentation." Carbohydrate Research
362: 38-46, 2012.
Liang, T. W.; Liu, C. P.; Wu, C.; Wang, S. L. "Applied development of crude enzyme from
Bacillus cereus in prebiotics and microbial community changes in soil." Carbohydrate Polymers
92(2): 2141-2148, 2013.
Lodhi, G.; Kim, Y. S.; Hwang, J. W.; Kim, S. K.; Jeon, Y. J.; Je, J. Y.; Ahn, C. B.; Moon, S. H.;
Jeon, B. T.; Park, P. J. "Chitooligosaccharide and its derivatives: preparation and biological
applications." BioMed Research International 2014 (1):1-13, 2014.
Lu, X.; Guo, H.; Zhang, Y. "Protective effects of sulfated chitooligosaccharides against
hydrogen peroxide-induced damage in MIN6 cells." International Journal of Biological
Macromolecules 50(1): 50-58, 2012.
Luo, Z.; Dong, X.; Ke, Q.; Duan, Q.; Shen, L. "Chitooligosaccharides inhibit ethanol-induced
oxidative stress via activation of Nrf2 and reduction of MAPK phosphorylation." Oncology
Reports,32(5): 2215-2222, 2014.
Fundamentação Teórica 26
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Luo, Z.; Dong, X.; Ke, Q.; Duan, Q.; Shen, L. "Downregulation of CD147 by
chitooligosaccharide inhibits MMP-2 expression and suppresses the metastatic potential of
human gastric cancer." Oncology Letters 8(1): 361-366, 2014a.
Ma, J.-X.; Qian, L.; Zhou, Y. "Stimulation effect of chitosan on the immunity of radiotherapy
patients suffered from lung cancer." International Journal of Biological Macromolecules 72(0):
195-198, 2015.
Masuda, S.; Azuma, K.; Kurozumi, S.; Kiyose, M.; Osaki, T.; Tsuka, T.; Itoh, N.; Imagawa, T.;
Minami, S.; Sato K.; Okamoto, Y. "Anti-tumor properties of orally administered glucosamine
and N-acetyl-d-glucosamine oligomers in a mouse model." Carbohydrate Polymers 111(0): 783-
787, 2014.
Moraes, C. C.; Mazutti, M. A.; Maugeri, F.; Kalil, S. J. "Modeling of ion exchange expanded-
bed chromatography for the purification of C-phycocyanin." Journal of Chromatography A
1281(0): 73-78, 2013.
Mourya, V. K.; Inamdar, N. N.; Choudhari, Y. M. "Chitooligosaccharides: Synthesis,
characterization and applications." Polymer Science Series A 53(7): 583-612, 2011.
Nelson, D. L.; Cox, M. "Lehninger Princípios de Bioquímica". 4 ed. São Paulo: Sarvier, 2006,
1202 p.
Ng, M. Y. T.; Tan, W. S.; Tey, B. T. "Purification of recombinant hepatitis B core antigen from
unclarified Escherichia coli feedstock using phage-immobilized expanded bed adsorption
chromatography." Journal of Chromatography B 903(0): 60-67, 2012.
Ngo, D.-H.; Qian, Z.-J; Vo, T.-S; Ryu, B.; Ngo, D.-N; Kim, S.-K. "Antioxidant activity of
gallate-chitooligosaccharides in mouse macrophage RAW264.7 cells." Carbohydrate Polymers
84(4): 1282-1288, 2011.
Fundamentação Teórica 27
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Nguyen, A. D.; Huang, C.-C.; Liang, T.-W.; Nguyen, V. B.; Pan, P.-S.; Wang, S.-L. "Production
and purification of a fungal chitosanase and chitooligomers from Penicillium janthinellum D4
and discovery of the enzyme activators." Carbohydrate Polymers 108(0): 331-337, 2014.
Nwe, N.; Furuike, T.; Tamura, H. "Isolation and characterization of chitin and chitosan from
marine origin." Advances in Food and Nutrition Research 72: 1-15,2014.
Oh, C.; De Zoysa, M.; Kang, D. H.; Lee, Y.; Whang, I.; Nikapitiya, C.; Heo, S. J.; Yoon, K. T.;
Affan, A.; Lee, J. "Isolation, purification, and enzymatic characterization of extracellular
chitosanase from marine bacterium Bacillus subtilis CH2." Journal of Microbiology and
Biotechnology 21(10): 1021-1025, 2011.
Padilha, C. E. A. Recuperação e purificação de quitosanases usando adsorção em leito expandido
com streamline DEAE com modelagem e simulação usando redes neurais. 2013. 129f.
Dissertação (Mestrado) – Universidade Federal do Rio Grande do Norte. Centro de Tecnologia.
Programa de Pós-Graduação em Engenharia Química. Natal, RN, 2013.
Pareek, N.; Vivekanand, V.; Agarwal, P.; Saroj, S.; Singh, R. P. "Bioconversion to chitosan: A
two stage process employing chitin deacetylase from Penicillium oxalicum SAEM-51."
Carbohydrate Polymers 96(2): 417-425, 2013.
Perrin, E.; Bizot, H.; Cathala, B.; Capron, I. "Chitin nanocrystals for Pickering high internal
phase emulsions." Biomacromolecules, 2014.
Punina, N. V.; Zotov, V. S.; Parkhomenko, A. L.; Parkhomenko, T. U.; Topunov, A. F. "Genetic
Diversity of Bacillus thuringiensis from Different Geo-Ecological Regions of Ukraine by
Analyzing the 16S rRNA and gyrB Genes and by AP-PCR and saAFLP." Acta Naturae 5(1): 90-
100, 2013.
Fundamentação Teórica 28
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Richardson, J. F.; Zaki, W. N. "Sedimentation and fluidisation: Part I". Chemical Engineering
Research and Design 75, Supplement(0):S82-S100, 1954.
Rhoades, J.; Gibson, G.; Formentin, K.; Beer, M.; Rastall, R. "Inhibition of the adhesion of
enteropathogenic Escherichia coli strains to HT-29 cells in culture by chito-oligosaccharides."
Carbohydrate Polymers 64(1): 57-59, 2006.
Seo, D.-J.; Lee, J.-H; Song, Y.-S.; Park, R.-D.; Jung, W.-J. "Expression patterns of chitinase and
chitosanase produced from Bacillus cereus in suppression of phytopathogen." Microbial
Pathogenesis 73(0): 31-36, 2014.
Sooch, B. S.; Kauldhar, B. S.; Puri, M. "Recent insights into microbial catalases: Isolation,
production and purification." Biotechnology Advances 2014(1): 1-19,2014.
Suma, K.; Podile, A. R. "Chitinase A from Stenotrophomonas maltophilia shows
transglycosylation and antifungal activities." Bioresource Technology 133: 213-220, 2013.
Takasuka, T. E.; Bianchetti, C. M.; Tobimatsu, Y.; Bergeman, L. F.; Ralph, J.; Fox, B. G.
"Structure-guided analysis of catalytic specificity of the abundantly secreted chitosanase
SACTE_5457 from Streptomyces sp. SirexAA-E." Proteins 82(7): 1245-1257, 2014.
Thadathil, N.; Velappan, S. P. "Recent developments in chitosanase research and its
biotechnological applications: a review." Food Chemistry 150: 392-399, 2014.
Trinh, M. D. L.; Ngo, D.-H.; Tran, D.-K.; Tran, Q.-T.; Vo, T.-S.; Dinh, M.-H.; Ngo, D.-N.
"Prevention of H2O2-induced oxidative stress in Chang liver cells by 4-hydroxybenzyl-
chitooligomers." Carbohydrate Polymers 103(0): 502-509, 2014.
Wang, S. L.; Peng, J.-H.; Liang, T.-W.; Liu, K.-C. "Purification and characterization of a
chitosanase from Serratia marcescens TKU011." Carbohydrate Research 343(8): 1316-1323,
2008.
Fundamentação Teórica 29
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Wang, S.L.; Yeh, P.-Y."Purification and characterization of a chitosanase from a nattokinase
producing strain Bacillus subtilis TKU007." Process Biochemistry 43(2): 132-138, 2008.
Wang, S. L.; Chang, T. J.; Liang, T. W. "Conversion and degradation of shellfish wastes by
Serratia sp. TKU016 fermentation for the production of enzymes and bioactive materials."
Biodegradation 21(3): 321-333, 2010.
Wang, S. L.; Liang, T.-W.; Yen, Y.-H. "Bioconversion of chitin-containing wastes for the
production of enzymes and bioactive materials." Carbohydrate Polymers 84(2): 732-742, 2011a.
Wang, S. L.; Tseng, W. N.; Liang, T. W. "Biodegradation of shellfish wastes and production of
chitosanases by a squid pen-assimilating bacterium, Acinetobacter calcoaceticus TKU024."
Biodegradation 22(5): 939-948, 2011b.
Wang, S. L.; Liu, C. P.; Liang, T. W. "Fermented and enzymatic production of chitin/chitosan
oligosaccharides by extracellular chitinases from Bacillus cereus TKU027". Carbohydrate
Polymers 90(3): 1305–1313, 2012.
Wilken, L. R.; Nikolov, Z. L. "Recovery and purification of plant-made recombinant proteins."
Biotechnology Advances 30(2): 419-433, 2012.
Wu, S.-J.; Pan, S.-K.; Wang, H.-B.; Wu, J.-H. "Preparation of chitooligosaccharides from cicada
slough and their antibacterial activity." International Journal of Biological Macromolecules
62(0): 348-351, 2013.
Yang, L.; Zhang, T.; Li, X. H.; Yu, R. "[Purification of a novel chitosanase from Metarhizium
guizhouense in solid-state fermentation with affinity chromatography]." Sichuan Da Xue Xue
Bao Yi Xue Ban 38(4): 713-716, 2007.
Fundamentação Teórica 30
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Younes, I.; Sellimi, S.; Rinaudo, M.; Jellouli, K.; Nasri, M. "Influence of acetylation degree and
molecular weight of homogeneous chitosans on antibacterial and antifungal activities."
International Journal of Food Microbiology 185(0): 57-63, 2014.
Zhang, C.-M.; Yu, S.-H.; Zhang, L.-S.; Zhao, Z.-Y.; Dong, L.-L. "Effects of several acetylated
chitooligosaccharides on antioxidation, antiglycation and NO generation in erythrocyte."
Bioorganic & Medicinal Chemistry Letters 24(16): 4053-4057, 2014a.
Zhang, H.; Fang, J.; Deng, Y.; Zhao, Y. "Optimized production of Serratia marcescens B742
mutants for preparing chitin from shrimp shells powders." International Journal of Biological
Macromolecules 69: 319-328, 2014b.
Zhang, H.; Zhao, X.; Yang, J.; Yin, H.; Wang, W.; Lu, H.; Du, Y. "Nitric oxide production and
its functional link with OIPK in tobacco defense response elicited by chitooligosaccharide."
Plant Cell Reports 30(6): 1153-1162, 2011.
Zhang, J.; Xia, W.; Liu, P.; Cheng, Q.; Tahirou, T.; Gu, W.; Li, B. "Chitosan modification and
pharmaceutical/biomedical applications." Marine Drugs 8(7): 1962-1987, 2010.
Zhang, P.; Liu, W.; Peng, Y.; Han, B.; Yang, Y. "Toll like receptor 4 (TLR4) mediates the
stimulating activities of chitosan oligosaccharide on macrophages." International
Immunopharmacology 23(1): 254-261, 2014c.
Zhang, P.; Zhou, W.; Wang, P.; Wang, L.; Tang, M. "Enhancement of chitosanase production by
cell immobilization of Gongronella sp. JG." Brazilian Journal of Microbiology 44(1): 189-195,
2013.
Zitouni, M.; Fortin, M.; Scheerle, R. K.; Letzel, T.; Matteau, D.; Rodrigue, S.; Brzezinski, R.
"Biochemical and molecular characterization of a thermostable chitosanase produced by the
strain Paenibacillus sp. 1794 newly isolated from compost." Applied Microbiology and
Biotechnology 97(13): 5801-5813, 2013.
Objetivos 32
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
4. OBJETIVOS
4.1. Objetivo geral
O objetivo geral do trabalho foi isolar e selecionar novos microrganismos produtores de
quitosanases com potencial de hidrólise da quitosana além de purificar e caracterizar as enzimas
obtidas, a fim de possibilitar a obtenção de quitosanases de forma mais rentável, e
consequentemente, de quitooligossacarídeos.
4.2. Objetivos específicos
Isolar, a partir de amostras de solo, microrganismos capazes de utilizar a
quitosana como principal fonte de carbono;
Selecionar os microrganismos isolados através da avaliação do potencial
hidrolítico das enzimas por eles produzidas;
Padronizar condições de cultivo dos microrganismos selecionados com o objetivo
de melhorar a produção das enzimas quitosanolíticas;
Determinar as condições ótimas de atividade das enzimas produzidas pelos
microrganismos previamente selecionados;
Recuperar e purificar a enzima com potencial quitosonalítico;
Caracterizar a quitosanase isolada quanto à (ao):
o Massa molecular;
o Efeito do pH sobre sua atividade enzimática;
o Efeito da temperatura sobre sua atividade enzimática;
o Dependência por íons bivalentes.
Artigos 34
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
5. ARTIGOS DERIVADOS DA TESE
A seguir serão apresentados dois artigos derivados da tese, submetidos para periódicos na
área.
O primeiro artigo intitulado “Recovery and Purification of Chitosanase produced by
Bacillus cereus using Expanded bed adsorption (EBA) and Central Composite Design (CCD)”
foi submetido ao periódico Separation Science and Technology, e o segundo “Single-step
purification of chitosanase from Bacillus cereus using expanded bed chromatography” foi
submetido ao Journal of Cromathography B.
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 35
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Recovery and Purification of Chitosanase produced by Bacillus cereus using Expanded
Bed Adsorption (EBA) and Central Composite Design (CCD)
Nathália Kelly de Araújo*, Maria Luiza Oliveira Xavier, Vanessa Carvalho Pimentel, Carlos
Eduardo de Araújo Padilha, Nayane Macedo Portela da Silva, Gorete Ribeiro de Macedo,
Everaldo Silvino dos Santos.
*Corresponding author at: Laboratório de Engenharia Bioquímica, Departamento de Engenharia Química, Universidade
Federal do Rio Grande do Norte – UFRN/Brazil. Phone: +55 84 3215 3769 R: 214. Fax: +55 84 3215 3770. E-mail
address: nakar_rn@hotmail.com (N. K.Araújo).
Abstract
This study presents a system for EBA to purification of chitosanase from broth extract in a
single step. A chitosanase-producing strain was isolated and identified as Bacillus cereus C-
01. Statistical analyses based showed that distributor height had strong influence on the
process affecting considerably both purification factor (P) and enzyme yield (Y). The
optimization of purification variables resulted in an approximately 3.66-fold increase in P
compared with that observed under not optimized conditions. This system is promising for
recovery of chitosanase from B. cereus C-01 and it is economically viability since it promotes
the reduction steps.
Keywords: Biocatalysis; Enzyme Activity; Chitosanase; Bioseparations; Chromatography;
Expanded bed adsorption.
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 36
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
INTRODUCTION
Derived from the hydrolysis of Chitosan, the Chitooligosaccharides (COS) have
several biofunctional properties, including anti-inflammatory [1], prebiotic [2], antimicrobial
[3], antitumor [4, 5], and immunopotentiating effects [6]. Thereby, the nutraceutical and
medical industries have been given special attention to production of chitooligosaccharides
from chitosan [7].
The depolymerization of chitosan is mainly conducted using acid hydrolysis and
enzymatic degradation. The acid hydrolysis is not usually employed due to the complexity of
control of the reaction. Moreover the use of acid promotes in the formation of secondary
compounds that are elimination difficult [8]. Enzymes exhibit high specificity and operate
under mild conditions. Additionally, the use of enzymes allows control of reaction and
product formation by adjusting the concentration of the enzyme, pH, temperature and
reaction time. Thus, enzyme technology probably is the most promising approach [9]. Several
enzymes can hydrolyze the chitosan; in this process are employed specific (chitosanases) and
non-specific enzymes (carbohydrases, proteases, lipases etc.) [10].
For applications requiring high purity (use in therapy and diagnosis), enzyme
purification may be necessary. The chromatography process conventional to remove product
and impurities are usually designed with steps of clarification, precipitation with salts and a
series of capture and polishing [11]. Expanded bed adsorption (EBA) is an integrated process
which combines solid-liquid separation, volume reduction by protein adsorption and
recovering the product in a single unit operation [11, 12]. This technique has been
successfully employed to biomolecules purification [13-16].
Optimization of the purification process can be performed using experimental design.
The estimate of the influential variables during the adsorption process can be determined by
correct selection of design and optimization models. The experimental design methodology
can be used to determine the effects of individual factors and their interactions [17]. Box and
Wilson developed a technique named is Central composite design (CCD) which use response
surface methodology. An advantage of CCD is the reduction of number of experiments in the
studies with a wide number of factors and levels [18]. Furthermore, by use of response
surface methodology (RSM), the main and interaction effects of variables can be explored
and optimal value of each variable can be definite [19].
The present study attempted to optimize the process of chitosanase purification by
EBA using a CCD with attention to both the purification factor (P) parameters as well as
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 37
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
enzyme yield (Y). A batch shake-flask culture of Bacillus cereus was used to enzyme
production.
MATERIALS AND METHODS
Materials
Chitosan (85 % deacetylated; molecular weight, 90–190 kDa) acquired from Sigma-
Aldrich Co. (St. Louis, Missouri, USA) was solubilized using 0.1 M HCl [20]. Streamline
DEAE resin was purchased from GE healthcare (Uppsala, Sweden). PC33 Siemens Kit was
provided by Maria Alice Hospital, Natal/Brazil. Buffer solutions and other chemicals were
reagent grade.
Isolation and identification of chitosanolytic bacterium
The microorganism was isolated from soil samples (Natal/Brazil, S 05º52’11’’, Wo
35º13’08.4’’). Serially diluted soil samples were inoculated on plates containing peptone (6.0
gL-1
), chitosan (2.0 gL-1
), Magnesium sulfate (0.5 gL-1
), Potassium dibasic phosphate (1.0 gL-
1) (basic medium) and agar (15 gL
-1) and incubated at 30 ºC for 2 days. A single colony
showing prominent chitosanolytic activity was selected and subjected to taxonomic analysis,
Gram-staining and pathogenicity test with PC33 Siemens Kit. To further identify the
bacterium, polymerase chain reaction (PCR) was performed to amplify part of the bacterial
16S rRNA gene. The forward and reverse primers were 27F (5’-AGA GTT TGA TCC TGG
CTC AG-3’) and 1525R (5’-AAG GAG GTG ATC CAG CC-3’), respectively. The PCR
products were analyzed by electrophoresis on agarose gel and after they were purified,
quantified and used in sequencing reaction. Four sequencing reactions were performed for
each sample using the primers 518F (5’-CCA GCA GCC GCG GTA ATA CG-3’), 800R
(5’-TAC CAG GGT ATC TAA TCC-3’) and 1492R (5’-TAC GGY TAC CTT GTTA
CGA CTT-3’). The nucleotide sequence of the 16S rRNA gene of C-01 was determined by
an ABI 3730 DNA Sequencer (Applied Biosystems, USA) and compared with published 16S
rRNA sequences in a NCBI BLAST search.
Chitosanase production
The cells from the stock cultures were transferred to 50 mL aliquots of pre-cultivation
medium dispensed into 250 mL Erlenmeyer flasks, then incubated at 120 rpm for 30 h at 30
ºC. The pre-cultivation medium consisted of (g.L−1
): peptone 6.0, chitosan 2.0, Magnesium
sulfate 0.5 and Potassium dibasic phosphate 1.0. This was then aseptically inoculated at a
level of 10% (v/v) into a 250 mL Erlenmeyer flask containing 50 mL of same medium. The
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 38
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
flasks were then placed on a rotary shaker at 120 rpm for 24 h at 30 ºC (Tecnal, TE421).
Samples of this cultivation were used for purification assay.
Analytical methods
The chitosanase activity of the crude enzyme and chromatography samples were
measured via the incubation of 250 μL of enzyme sample with 250 μL of 1% chitosan
solution (pH 6.0). The mixture was heated in a water bath for 30 minutes, at a temperature
adjusted to 55 ºC. The reaction was interrupted by boiling for 10 minutes [20]. The
formation of reducing sugars was analyzed in spectrophotometer (Thermo Spectronic) using
the 3,5-Dinitrosalicylic acid method, using D-glucosamine as standard [21]. A unit (U) of
chitosanase was defined as the amount of enzyme capable of generating 1 µmol of D-
glucosamine per minute under the conditions above described.
The protein content was determined using the Bicinchoninic Acid method with a BCA
Protein Assay Kit (Pierce, Rockford, IL) and Bovine Serum Albumin (BSA) as standard.
Experimental Designs
The optimization strategy that was used is based on the concept of simultaneous
variation of possible influencing factors (independent variable) on the quality criteria
(dependent variable) of the system considered. This strategy was used to evaluate the
influence of three factors on the enzyme purification. Dependents variable were defined on
the quality criteria purification factor (P) and enzyme yield (Y) to optimize the
chromatographic process:
𝑃 =𝑆𝑝𝑒𝑐𝑖𝑓𝑖𝑐 𝑎𝑐𝑡𝑖𝑣𝑖𝑡𝑦 𝑜𝑓 𝑡ℎ𝑒 𝑝𝑢𝑟𝑖𝑓𝑖𝑒𝑑 𝑠𝑎𝑚𝑝𝑙𝑒
𝑆𝑝𝑒𝑐𝑖𝑓𝑖𝑐 𝑎𝑐𝑡𝑖𝑣𝑖𝑡𝑦 𝑜𝑓 𝑡ℎ𝑒 𝑐𝑟𝑢𝑑𝑒 𝑠𝑎𝑚𝑝𝑙𝑒 Eq.1
𝑌(%) =𝐸𝑛𝑧𝑦𝑚𝑎𝑡𝑖𝑐 𝑎𝑐𝑡𝑖𝑣𝑖𝑡𝑦 𝑜𝑓 𝑡ℎ𝑒 𝑝𝑢𝑟𝑖𝑓𝑖𝑒𝑑 𝑠𝑎𝑚𝑝𝑙𝑒
𝐸𝑛𝑧𝑦𝑚𝑎𝑡𝑖𝑐 𝑎𝑐𝑡𝑖𝑣𝑖𝑡𝑦 𝑜𝑓 𝑡ℎ𝑒 𝑐𝑟𝑢𝑑𝑒 𝑠𝑎𝑚𝑝𝑙𝑒 Eq.2
A CCD was employed to examine the combined and individual effect of three
independent variables for chitosanase purification. The CCD is usually characterized by three
operations: 2k axial runs, 2k factorial runs and central point runs [19]. The number of
experiments (N), represented by Equation 3, depends on how many factors (k) are in the
CCD:
N=2k + 2k + central points Eq. 3
The CCD in this study was designed based in 6 axial points, 8 factorial points and 3
replicates at the center. Initially, it was constructed the factorial and central parts, followed by
the axial one. The quantitative factors were load flow velocity (X1), settled bed height (X2)
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 39
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
and distributor height (X3) utilized as independent variables for the CCD. The experimental
design with coded and uncoded values is presented in Table 1.
Table 1: Matrix of CCD to coded and uncoded level of independent variables.
Variables
Levels
-α -1 0 +1 +α
Load flow velocity (cm/h) 66 100 150 200 234
Settled bed height (cm) 2.64 4.0 6.0 8.0 9.36
Distributor height (cm) 0.64 2.0 4.0 6.0 7.36
From a second-order polynomial equation is possible to explain the behavior of each
variable, their interactions, and statistical analysis and acquire predicted responses [7]. The
following second-order polynomial Equation was used:
Y = b0 + ∑ bixi + ∑bijxixj + ∑biix2
i Eq.4
Where Y is the predicted response, b0 is the model constant, bi is the linear
coefficients, bii are the quadratic coefficients and bij is the interaction coefficients. Xi
represents the independent variables (known for each run). The experimental design analysis
and their subsequent regression analysis were evaluated using STATISTICA 7.0 (StatSoft,
USA). The analysis of variance (ANOVA) was also carried out. The p-values less than 0.05
(p <0.05) were considered statistically significant.
The optimized conditions from statistical model were validated and the chitosanase
purification was evaluated. The validation assay was conducted with 150 cm.h-1
load flow
velocity, 6.0 cm settled bed height and 7.36 cm distributor height. The samples were
withdrawn at appropriate intervals, which were subjected to further analysis in terms of
chitosanase activity and protein concentration.
Operation of EBA
The ligand Diethylaminoethyl (DEAE) of the streamline ion exchanger (GE
Healthcare, Uppsala, Sweden) was applied to EBA chromatography. This resin is a weak
anionic exchanger. A homemade EBA glass column (2.6 cm x 30.0 cm) was used. A different
amount of glass microspheres was added to work as a distributor, i.e., to enhance fluid
distribution at the column inlet. The peristaltic pump was used to transport the fluid (model
Perimax 12, Spetec). The correct column vertical alignment was guaranteed in all assays. All
experiments were performed at the room temperature.
Runs were conducted without clarification. The column with different settled-bed
height of resins was equilibrated with a 50mM Tris-HCl pH 8.5 buffer (buffer A) to give a
stable height, where H/H0=1.5. The broth was then loaded (flow-through step) onto this
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 40
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
column at the superficial velocity required according to Table 1, following the washing with
buffer A (150 mL). The elution was performed by step-wise gradient mode with 50 mM Tris-
HCl pH 8.5 buffer containing 0.3 M (buffer B), 0.7 M (buffer C), and 1 M (buffer D) NaCl.
Both washing and elution were conducted at the superficial velocity of 100 cm.h−1
. In all
purification steps, several fractions were collected for protein quantification and enzyme
assay.
RESULTS AND DISCUSSION
Identification of chitosanase-producing strain
The microorganism was isolated from soil samples using procedure described in
section 2.2. Among over 15 strains were isolated in the laboratory and screened for
chitosanase activity, the Bacillus C-01 strain was selected for further study. This strain
showed the highest chitosanase activity. Strain C-01 is a gram-positive, which grows in both
aerobic and anaerobic environments. The culture showed colonies with rounded, irregular
border, average size of 4 mm and white coloring. According to the results of 16S rDNA
partial nucleotide sequence analysis, strain C-01 was identified as B. cereus.
CCD and Model fitting
As observed with EBA systems, several factors have to be considered for the
optimization of protein purification. Such as, load flow velocity, settled bed height and
distributor height [22, 23]. The chitosanase purification was optimized using statistical
experimental design involving three variables, namely load flow velocity (X1,) settled bed
height (X2) and distributor height (X3), at five levels. Table 2 presents the Central Composite
design variables (coded levels) and effect estimates for screening of factors affecting P and Y.
The best values of the P were obtained on the assay 17 and 14. In other assays, it can
be observed low values purification factor. This fact can be related to the strong interaction of
biomass with the resin. Similar results were also observed by [24], whereby the purification
factor varied in function of feedstock. The performance of many direct-contact methods for
downstream processing of bioproducts can be affected by biomass adhesion or interaction.
Biological feedstock can also severely affect this process by particles co-adhesion or
aggregation [25].
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 41
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Table 2. Central Composite design variables (coded factor and levels) and effect estimates for screening of
factors affecting purification factor (P) and enzyme yield (Y).
Coded Variable levels
Run number. X1 X2 X3 P Y
1 -1 -1 -1 1.18 45.12
2 +1 -1 -1 0.51 17.03
3 -1 +1 -1 0.92 43.47
4 +1 +1 -1 0.90 39.67
5 -1 -1 +1 1.24 46.92
6 +1 -1 +1 1.27 47.27
7 -1 +1 +1 0.64 27.26
8 +1 +1 +1 0.74 29.99
9 (C) 0 0 0 0.54 22.44
10 (C) 0 0 0 0.53 21.35
11 (C) 0 0 0 0.59 23.26
12 -α 0 0 0.89 39.61
13 +α 0 0 1.01 22.61
14 0 -α 0 1.40 35.40
15 0 +α 0 0.85 28.63
16 0 0 -α 1.10 31.79
17 0 0 +α 1.43 34.79
Effect estimates I*
-0.05(L)
0.18(Q)
-0.28(L)
0.31(Q)
0.13(L)
0.39(Q)
Effect estimates II**
-8.40(L)
8.12(Q)
-4.00(L)
8.76(Q)
1.64(L)
9.67(Q)
X1, load flow velocity (cm.h-1); X2, settled bed height (cm); X3, distributor height (cm); P, purification factor; Y, enzyme yield (%); *Effect
estimates I, for purification factor; **Effect estimates II for enzyme yield. (C): center point.
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 42
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
As can be observed in Table 2, intermediary conditions do not improve either P or Y.
Even though all factors play role in both P and Y it can be seen that Distributor Height (X3)
and its interaction with other factors were the most important. The main effects of variables
on P and Y are also shown in Table 2. On the basis of statistical analysis for quadric model,
the variables evidencing the most significant effects on P and Y were settled bed height and
distributor height as well as their interactions.
Analysis of variance (ANOVA)
Table 3 presents the results of the analysis of variance (ANOVA). The variables with
confidence levels exceeding 95% (p < 0 .05) were considered to be significant. The goodness
of model fit was checked by the determination coefficient (R2). The ANOVA of regression
model demonstrated that the R2 to P and Y were 0.835 and 0.9147, respectively, thus
indicating that about 90% of the variability in the response could explained by the model. The
value of the adjusted determination coefficient (Adj. R2 = 0.623 for P and 0.805 for Y) is also
acceptable, which indicates a high significance of the model.
Table 3: Analysis of variance (ANOVA) for central composite design of purification factor and enzyme
yield.
Variable Adj R2 (%) R
2 (%) Fcal Ftab Fcal/Ftab
Purification Factor (P) 62.3 83.5 4.171 3.68 1.13
Enzyme Yield (Y) 80.5 91.4 48.02 3.68 13
By ANOVA and regression coefficients can be deduced that the quadratic model
showed high adequacy for the explanation of adsorption behavior. For purification factor, the
most influential variables were the X3 (Q) (p value 0.001977), X2 (L) (p value 0.003015) and
X2 (Q) (p value 0.003052). The interaction X2X3 also presents strong influence about P.
For Y, the most influential variables were the interaction X2X3 (p value 0.002195), X3
(Q) (p value 0.003483) and X1 (L) (p value 0.003805).
By regression analysis of CCD, it was possible to obtain the following Equation for P
and Y:
YP= 0.570 -0.027X1 +0.091X12 – 0.144X2 + 0.158X2
2 + 0.064X3 + 0.196X3
2 + 0.090X1X2 +
0.120X1X3 – 0.159X2X3 Eq.5
YR= 22.073 – 4.203X1 + 4.064X12 – 2.00X2 + 4.384X2
2 + 0.820X3 + 4.836X3
2 + 3.333X1X2 +
4.371X1X3 – 7.24X2X3 Eq. 6
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 43
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Where YP is the response for purification factor and YR is the response for enzyme
yield. X1, X2 and X3 are the coded values of the test variables (load flow velocity, settled bed
height and distributor height, respectively).
By F test can be seen that the proposed models (Equations 5 and 6) are statistically
significant. As for P, Fcal value was 1.3 times greater than Ftab. Already for the Y, the
observed difference was much higher: 13 times larger than Ftab (Table 3).
Response surface methodology (RSM)
CCD, Box-Behnken design and three-level factorial design are classes of RSM and
have different characteristics. Among the most popular techniques, the CCD allows
optimization and estimation of the main and interaction of variables with least number of
experiments [19].
Figure 1 shows the response surface and contour plots for variation in P and Y versus
significant variables. The surface plots confirm that the interactions between the independent
variables have a strong effect on response variables. The combined decrease in load flow
velocity and settled bed height contribute to the increase of P (Figure 1a). The load flow
velocity and distributor height need to be at the same level to improve the purity. High values
of speed and distribution height combined increase the purity as well as low values of speed
combined with low values of distributor height also raise the purity (Figure 1b). While an
increase in distributor height of the combined with a decrease in settled bed height
contributes to the increase in purity (Figure 1c).
The decrease in load flow velocity leads to significant increase in Y (Figures 2d and
2e). Whereas that increase in distributor height and settled bed height lead to significant
increase in Y (Figures 1e and 1f).
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 44
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figure 1: Response surfaces for 23 central composite designs (a) X1 – X2 (purification factor); (b) X1 – X3
(purification factor); (c) X2 – X3 (purification factor); (d) X1 – X2 (Enzyme yield); (e) X1 – X3 (Enzyme yield);
(f) X2 – X3 (Enzyme yield). X1, load flow velocity; X2, settled bed height; X3, distributor height. Other
variables, except for two variables in each figure, were maintained at zero in coded units.
In this study the parameters settled bed height and distributor height show different
behaviors. We believe that biomass, resin and distributor interaction is so strong that
determine the effect on the response variable. The influence of biomass on the hydrodynamic
stability of expanded beds has been demonstrated by several researches [22, 24, 26]. The
distributor has a great action on the flow structure [23]. For responses Y the distributor height
has a positive effect. When the distributor height is increased, there is less back-mixing
effect. The flow is more homogeneous, and it promotes the adsorption. A smaller mixture
favors the plug-flow. Therefore, it can be conclude that the optimum conditions are far from
the central point, as can be seen in Figure 1.
To check the normality assumption in fitted model, It was plotted the predicted versus
the observed for P and Y (Figure 2). The figures exhibit linear relationship between predicted
and observed. The measured response was really close to the predicted.
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 45
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figure 2: The experimental data versus the predicted data of normalized of purification factor (a) and enzyme
yield (b).
Test of the model
Validation experiments were conducted to ensure the adjustment of the model for
chitosanase purification. This assay was carried out under following conditions: load flow
velocity 150 cm.h-1
, 6.0 cm of settled bed height and 7.36 cm distributor height. Figure 3
shows the chromatogram for chitosanse purification. The elution step was carried out with the
NaCl gradient. In the first increase in ionic strength, a peak of enzyme activity and protein
concentration was obtained.
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 46
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figure 3: Chromatographic profile of crude extract from Bacillus cereus in streamline DEAE ion exchange
column. The column was previously equilibrated with 50 mM Tris-HCl, pH 8.5 (Buffer A) and the sample was
eluted from column with 50 mM Tris-HCl buffer, pH 8.5 containing 0.3, 0.7 and 1.0M NaCl (Step wise).
The validation experiment with three replicates resulted in an average P of 1.46 (±
0.12), while the P predicted for this assay by the regression model was 1.23. Under not
optimized conditions (central point), the P mean was 0.55 (± 0.032) therefore the
optimization resulted in an approximately 2.65-fold increase. The average Y for validation
experiment was 34% (± 1.6), the predicted value of Y by the regression model was 37%. The
average Y in central point was 22.5 (± 0.96), what indicates 1.65-fold increase.
This study was generally consistent with the results to packed purification of another
chitosanases that were reported to a final yield of 23.6% [27], 30% [28] and 17.1% [29]. To
applications on unpacked bed purifications, these results are similar to those found in the
purification of a C-phycocyanin [14], an E. coli-Based therapeutics [18] and β-galactosidase
[30]. It is important to highlight that the procedure used here has just one-step, and can be
coupled to another EBA procedure such as cationic as well as hydrophobic interaction.
CONCLUSION
In the present study a CCD was used to optimize the application of the EBA, based on
anionic exchange, to recover as well as to purify a chitosanase from Bacillus cereus. This
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 47
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
statistical experimental approach confirmed to be effective for the optimization of
chitosanase purification. CCD analyses showed that the optimum conditions for maximum P
were 150 cm.h-1
(load flow velocity), 6.0 cm for the settled bed height and 7.36 cm for the
distributor height. The validation experiments proved that optimum conditions enhance the
purification factor and also evidenced a good applicability of model. This study provides
knowledge about hydrodynamics as well as biomass interaction in the purification protocol of
biomolecules by EBA. Furthermore, the system is promising for recovery of chitosanase from
B. cereus C-01 and it is economically viability since it promotes the reduction steps.
Acknowledgements
The authors thank the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior and
the Conselho Nacional de Desenvolvimento Científico e Tecnológico for financial support.
Conflicts of Interest
The authors declare no conflict of interest.
REFERENCES
[1] K. Azuma, T. Osaki, S. Kurozumi, M. Kiyose, T. Tsuka, Y. Murahata, T. Imagawa, N.
Itoh, S. Minami, K. Sato, Y. Okamoto, Anti-inflammatory effects of orally administered
glucosamine oligomer in an experimental model of inflammatory bowel disease,
Carbohydrate polymers, 115 (2015) 448-456.
[2] X.F. Kong, X.L. Zhou, G.Q. Lian, F. Blachier, G. Liu, B.E. Tan, C.M. Nyachoti, Y.L.
Yin, Dietary supplementation with chitooligosaccharides alters gut microbiota and modifies
intestinal luminal metabolites in weaned Huanjiang mini-piglets, Livestock Science, 160
(2014) 97-101.
[3] I. Younes, S. Sellimi, M. Rinaudo, K. Jellouli, M. Nasri, Influence of acetylation degree
and molecular weight of homogeneous chitosans on antibacterial and antifungal activities,
International Journal of Food Microbiology, 185 (2014) 57-63.
[4] C.F. de Assis, L.S. Costa, R.F. Melo-Silveira, R.M. Oliveira, M.G. Pagnoncelli, H.A.
Rocha, G.R. de Macedo, E.S. Santos, Chitooligosaccharides antagonize the cytotoxic effect
of glucosamine, World J Microbiol Biotechnol, 28 (2012) 1097-1105.
[5] S. Masuda, K. Azuma, S. Kurozumi, M. Kiyose, T. Osaki, T. Tsuka, N. Itoh, T. Imagawa,
S. Minami, K. Sato, Y. Okamoto, Anti-tumor properties of orally administered glucosamine
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 48
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
and N-acetyl-d-glucosamine oligomers in a mouse model, Carbohydrate Polymers, 111
(2014) 783-787.
[6] P. Zhang, W. Liu, Y. Peng, B. Han, Y. Yang, Toll like receptor 4 (TLR4) mediates the
stimulating activities of chitosan oligosaccharide on macrophages, International
Immunopharmacology, 23 (2014) 254-261.
[7] Y.-J. Wee, L.V.A. Reddy, K.-C. Chung, H.-W. Ryu, Optimization of chitosanase
production from Bacillus sp. RKY3 using statistical experimental designs, Journal of
Chemical Technology & Biotechnology, 84 (2009) 1356-1363.
[8] G. Lodhi, Y.S. Kim, J.W. Hwang, S.K. Kim, Y.J. Jeon, J.Y. Je, C.B. Ahn, S.H. Moon,
B.T. Jeon, P.J. Park, Chitooligosaccharide and its derivatives: preparation and biological
applications, Biomed Res Int, 2014 (2014) 654913.
[9] V.K. Mourya, N.N. Inamdar, Y.M. Choudhari, Chitooligosaccharides: Synthesis,
characterization and applications, Polym. Sci. Ser. A, 53 (2011) 583-612.
[10] N. Thadathil, S.P. Velappan, Recent developments in chitosanase research and its
biotechnological applications: a review, Food Chem, 150 (2014) 392-399.
[11] X. Xu, J. Hirpara, K. Epting, M. Jin, S. Ghose, S. Rieble, Z.J. Li, Clarification and
capture of high-concentration refold pools for E. coli-based therapeutics using expanded bed
adsorption chromatography, Biotechnology Progress, 30 (2014) 113-123.
[12] F.B. Anspach, D. Curbelo, R. Hartmann, G. Garke, W.-D. Deckwer, Expanded-bed
chromatography in primary protein purification, Journal of Chromatography A, 865 (1999)
129-144.
[13] S. de Santana, R. da Silva Filho, J. dos Santos Cavalcanti, J. de Oliveira, G. de Macedo,
F. Padilha, E. dos Santos, Modeling and simulation of breakthrough curves during
purification of two chitosanases from Metarhizium anisopliae using ion-exchange with
expanded bed adsorption chromatography, Korean J. Chem. Eng., 31 (2014) 684-691.
[14] C.C. Moraes, M.A. Mazutti, F. Maugeri, S.J. Kalil, Modeling of ion exchange expanded-
bed chromatography for the purification of C-phycocyanin, Journal of chromatography. A,
1281 (2013) 73-78.
[15] Y. Li, N. Wang, M. Zhang, Y. Ito, H. Zhang, Y. Wang, X. Guo, P. Hu, Development of
a method to extract and purify target compounds from medicinal plants in a single step:
online hyphenation of expanded bed adsorption chromatography and countercurrent
chromatography, Analytical chemistry, 86 (2014) 3373-3379.
[16] F.C. de Sousa Junior, M.R.F. Vaz, C.E. de Araújo Padilha, A.S. Chibério, D.R.A.
Martins, G.R. de Macedo, E.S. dos Santos, Recovery and purification of recombinant 503
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 49
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
antigen of Leishmania infantum chagasi using expanded bed adsorption chromatography,
Journal of Chromatography B, 986–987 (2015) 1-7.
[17] M. Roosta, M. Ghaedi, A. Daneshfar, S. Darafarin, R. Sahraei, M.K. Purkait,
Simultaneous ultrasound-assisted removal of sunset yellow and erythrosine by ZnS:Ni
nanoparticles loaded on activated carbon: optimization by central composite design,
Ultrasonics sonochemistry, 21 (2014) 1441-1450.
[18] H. Xu, J. Paxton, J. Lim, Y. Li, Z. Wu, Development of a gradient high performance
liquid chromatography assay for simultaneous analysis of hydrophilic gemcitabine and
lipophilic curcumin using a central composite design and its application in liposome
development, Journal of Pharmaceutical and Biomedical Analysis, 98 (2014) 371-378.
[19] M. Ghaedi, H. Mazaheri, S. Khodadoust, S. Hajati, M.K. Purkait, Application of central
composite design for simultaneous removal of methylene blue and Pb2+ ions by walnut wood
activated carbon, Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy,
135 (2015) 479-490.
[20] N.K. de Araujo, C.F. de Assis, E.S. Dos Santos, G.R. de Macedo, L.F. de Farias, H.
Arimateia, Jr., M. de Freitas Fernandes Pedrosa, M.G. Pagnoncelli, Production of enzymes by
Paenibacillus chitinolyticus and Paenibacillus ehimensis to obtain chitooligosaccharides,
Applied biochemistry and biotechnology, 170 (2013) 292-300.
[21] G.L. Miller, Use of Dinitrosalicylic Acid Reagent for Determination of Reducing Sugar,
Analytical chemistry, 31 (1959) 426-428.
[22] D.-Q. Lin, J. Thömmes, M.-R. Kula, J.J. Hubbuch, The influence of biomass on the
hydrodynamic behavior and stability of expanded beds, Biotechnology and Bioengineering,
87 (2004) 337-346.
[23] C. Sobrino, N. Ellis, M. de Vega, Distributor effects near the bottom region of turbulent
fluidized beds, Powder Technology, 189 (2009) 25-33.
[24] M.Y. Ng, W.S. Tan, N. Abdullah, T.C. Ling, B.T. Tey, Effect of different operating
modes and biomass concentrations on the recovery of recombinant hepatitis B core antigen
from thermal-treated unclarified Escherichia coli feedstock, Journal of biotechnology, 138
(2008) 74-79.
[25] R. Vennapusa, S.M. Hunegnaw, R.B. Cabrera, M. Fernandez-Lahore, Assessing
adsorbent-biomass interactions during expanded bed adsorption onto ion exchangers utilizing
surface energetics, Journal of chromatography. A, 1181 (2008) 9-20.
Recovery and Purification of Chitosanase produced by Bacillus cereus using EBA and CCD 50
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
[26] F. Poulin, R. Jacquemart, G. De Crescenzo, M. Jolicoeur, R. Legros, A Study of the
interaction of HEK-293 cells with streamline chelating adsorbent in expanded bed operation,
Biotechnol Prog, 24 (2008) 279-282.
[27] T.W. Liang, Y.Y. Chen, P.S. Pan, S.L. Wang, Purification of chitinase/chitosanase from
Bacillus cereus and discovery of an enzyme inhibitor, International journal of biological
macromolecules, 63 (2014) 8-14.
[28] X. Jiang, D. Chen, L. Chen, G. Yang, S. Zou, Purification, characterization, and action
mode of a chitosanase from Streptomyces roseolus induced by chitin, Carbohydrate research,
355 (2012) 40-44.
[29] S.K. Hsu, Y.C. Chung, C.T. Chang, H.Y. Sung, Purification and characterization of two
chitosanase isoforms from the sheaths of bamboo shoots, Journal of agricultural and food
chemistry, 60 (2012) 649-657.
[30] V. Boeris, I. Balce, R.R. Vennapusa, M. Arevalo Rodriguez, G. Pico, M.F. Lahore,
Production, recovery and purification of a recombinant beta-galactosidase by expanded bed
anion exchange adsorption, Journal of chromatography. B, Analytical technologies in the
biomedical and life sciences, 900 (2012) 32-37.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 51
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Single-step purification of chitosanase from Bacillus cereus using expanded bed
chromatography
Nathália Kelly de Araújoa,*
, Maria Giovana Binder Pagnoncellib, Vanessa Carvalho Pimentel
a, Maria Luiza Oliveira
Xaviera, Carlos Eduardo Araújo Padilha
a, Gorete Ribeiro de Macedo
a, Everaldo Silvino dos Santos
a
aLaboratório de Engenharia Bioquímica, Departamento de Engenharia Química, Universidade Federal do Rio Grande do Norte
– UFRN/Brazil
bLaboratório de Bromatologia, Departamento de Farmácia, Universidade Federal do Rio Grande do Norte – UFRN/Brazil.
*Corresponding author at: Laboratório de Engenharia Bioquímica, Departamento de Engenharia Química, Universidade
Federal do Rio Grande do Norte – UFRN/Brazil. Phone: +55 84 3215 3769 R: 214. Fax: +55 84 3215 3770. E-mail address:
nakar_rn@hotmail.com (N. K.Araújo).
Abstract
A chitosanase-producing strain was isolated and identified as Bacillus cereus C-01.The
purification and characterization of the chitosanase were studied. An ion exchange expanded-bed
chromatography was used for the purification of the chitosanase. Experiments were carried out in
the presence and in the absence of cells through different expansion degree to evaluate the
process performance. The adsorption experiments demonstrated that the biomass does not affect
substantially the adsorption capacity of the matrix. The enzyme bound to the resin with the same
extent using clarified and unclarified broth (0.32 and 0.30 U/g adsorbent, respectively). The
fraction recovered after the elution exhibited 31% of the yield with a 3.6-fold increased specific
activity concerned to the initial broth. The fraction eluted with 0.3 M NaCl achieved a
purification factor of 1.75. The purified chitosanase showed stability at 30 - 60 ºC, pH 5.5 – 8.0
with the highest activity at 55 ºC, pH 5.5. The ions Cu+2
, Fe+2
and Zn+2
indicated inhibitory effect
for chitosanase. In contrast, the enzyme was significantly activated by Mn2+
.The methodology
applied in this study enables the partially purification of a stable chitosanase using a feedstock
without any pre-treatment in a single-step purification.
Keywords: Chitosan; Chitosanase; Bacillus cereus; Bioseparation; Ion exchange; Expanded Bed
Adsorption.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 52
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
INTRODUCTION
Chitosan, a natural cationic polysaccharide, is produced by the deacetylation of chitin.
The chitosan molecule has shown various properties such as functional, renewable, nontoxic and
biodegradable biopolymer. In recent years, chitosan has been used as artificial skin, absorbable
surgical suture, wound healing accelerator and also as chitoligosaccharides (COS) source [1].
The oligosaccharides from chitosan have many biological properties such as: antitumor [2, 3],
immunoenhancing [1], antibacterial [4, 5], antidiabetic [6] and hypocholesterolemic [7]. These
functions are dependent of oligosaccharide chemical structure and molecular size [1, 8].
The COS are obtained mainly using chemical and/or enzymatic hydrolysis [8]. Enzymes
are highly specific and act under mild conditions. Moreover, the use of enzymes allows reaction
control and the product formation by adjusting concentration, pH, temperature and reaction time
[9]. Thus, the enzymatic hydrolysis method has been proposed as a preferred for producing
bioactive COS [10].
Chitosanases have previously been produced by a number of organisms, including fungi
[2, 11], plants [12], and bacteria [13, 14]. The chitosanases produced by Bacillus cereus are
currently investigated by several studies [15-20]. The process to purification of these enzymes
normally involves ammonium sulfate precipitation, gel filtration and packed ion exchange
chromatography [16, 21-23]. These traditional methods imply in a large number of steps,
extensive work time and scale up difficulties. Alternatively, the Expanded Bed Adsorption
(EBA) combines separation, concentration and capture of the target protein. This competitive
biotechnological process has been proposed as a single-unit operation [24]. EBA allows the
capture target proteins from feedstock without any pre-clarification steps, which is helpful to
industrial processes since it contributes to reduction of time and costs [25].
The aim of this present study was to evaluate chitosanase purification using an economic
and a fast chromatographic method. Initially, the adsorption behaviour of chitosanase onto
Streamline-DEAE as well as biomass influence were either determined. After, a purification
protocol was carried out in order to recover and purify the chitosanase.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 53
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
MATERIALS AND METHODS
Materials
Chitosan (85% deacetylated; molecular weight: 90–190 kDa) acquired from Sigma-
Aldrich Co. (Saint Louis, USA) was solubilized using 0.1 M HCl [14]. Streamline DEAE resin
was purchased from GE healthcare (Uppsala, Sweden). BCA Protein Assay Kit was acquired
from Pierce (Rockford, USA).PC33 Siemens Kit was provided by Maria Alice Hospital,
Natal/Brazil. Buffer solutions and other chemicals were reagent grade and were used as supplied.
Isolation and identification of chitosanolytic bacterium
The microorganism was isolated from soil samples (Natal/Brazil S 05º52’11’’, Wo
35º13’08.4’’). Serially dilutions from soil samples were inoculated on plates containing peptone
(6.0 gL-1
), chitosan (2.0 gL-1
), magnesium sulfate (0.5 gL-1
), potassium dibasic phosphate (1.0
gL-1
) and agar (15 gL-1
) and incubated at 30 ºC for 2 days. A single colony showing prominent
chitosanolytic activity was selected and subjected to morphological analyses, Gram-staining and
pathogenicity test with PC33 Siemens Kit. Polymerase chain reaction (PCR) was performed to
amplify part of the bacterial 16S rRNA gene to additional microbial identification. The forward
and reverse primers were 27F (5’-AGA GTT TGA TCC TGG CTC AG-3’) and 1525R (5’-AAG
GAG GTG ATC CAG CC-3’), respectively. The PCR products were analysed by electrophoresis
on agarose gel. Subsequently, they were purified, quantified and used in sequencing reaction.
Four sequencing reactions were run for each sample using the primers 518F (5’-CCA GCA
GCC GCG GTA ATA CG-3’), 800R (5’-TAC CAG GGT ATC TAA TCC-3’) and 1492R
(5’-TAC GGY TAC CTT GTTA CGA CTT-3’). The nucleotide sequence of the 16S rRNA gene
of C-1 was determined by an ABI 3730 DNA Sequencer (Applied Biosystems, USA) and
compared to16S rRNA sequences in a NCBI BLAST search.
Chitosanase production
Cells from the stock cultures were transferred to 50 mL aliquots of medium and
dispensed into 250 mL Erlenmeyer flasks for the investigation of chitosanase production.
Subsequently, they were incubated at 120 rpm for 72 h at 30 ºC. The cultivation medium
consisted of (g.L−1
): peptone 6.0, chitosan 2.0, magnesium sulfate 0.5 and potassium dibasic
phosphate 1.0. During cultivation, the culture broth was collected to measurement of chitosanase
activity and protein content. Cell growth was monitored by extraction and quantification of total
DNA content. The pellet of 3 mL of culture was used for DNA extraction using Sodium Dodecyl
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 54
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Sulfate (SDS) and phenol/chloroform/isoamyl alcohol [26]. The culture broth was used for
further purification by using Expanded Bed Adsorption (EBA).
Hydrodynamic of the bed
The expansion characteristic of the bed was investigated with an initial settled bed height
of 6.0 cm at 25 ºC. The bed expansion height was visually checked as a function of incrementing
velocity ranging from 30 to 200 cm.h-1
. The expansion degree to each velocity was registered
and expressed as the ratio of the height of the expanded (H) to the settled (H0) bed adsorbent.
The flow rate was kept constant for 10 minutes in each step before the estimation of the bed
height to ensure bed stabilization. The experiments were carried out using culture broth with
cells and without cells. The cells were removed by centrifugation for 20 minutes (4 ºC, 3000
rpm).
The empirical correlation of Richardson-Zaki [27] was applied to define the bed
expansion characteristics:
𝑢 = 𝑢𝑇 . 𝜀𝑛 Eq.1
u is the superficial velocity, ε is the bed porosity, uT is the terminal velocity in infinite medium
and n is the exponent of Richardson-Zaki which expresses the flow regime. The settled bed
voidage was considered to have a value of 0.4 according to [28]. All experiments were carried
out in triplicate.
Operation of EBA
The purification assays were developed using EBA methodology. The streamline anionic
exchanger resin containing the ligand Diethylaminoethyl (DEAE) and a homemade EBA column
(2.6 cm x 30.0 cm) were used to EBA chromatography. Glass microspheres were added to
enhance fluid distribution at the column inlet. The fluid was transported using a peristaltic pump
(model Perimax 12, Spetec). The vertical alignment of the column was guaranteed in all assays.
All experiments were performed at room temperature.
The column with 6.0 cm settled-bed height of resin was equilibrated with 50 mM Tris-
HCl pH 8.5 buffer (buffer A) to give a stable expansion degree of H/H0=1.5. The culture broth
was then loaded (flow-through step) onto column at 150 cm.h-1
superficial velocity. After, the
bed was washed with buffer A (150mL). The elution was carried out by step-wise gradient mode
with 50mM Tris-HCl pH 8.5 buffer containing 0.3 M (buffer B), 0.7 M (buffer C), and 1 M
(buffer D) NaCl. The both steps, washing and elution, were conducted at the superficial velocity
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 55
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
of 100 cm.h−1
. In all purification steps, several fractions were collected for protein quantification,
enzyme assay and electrophoresis.
Dynamic binding capacity
The adsorption performance of the expanded bed was studied in an EBA column loaded
with streamline DEAE to a settled bed height of 6.0 cm. The effect of microbial cells on the
breakthrough curves behaviour was studied. The bed was expanded to an expansion degree of
2.0 with buffer A at a superficial velocity of 150 cm.h-1
. Subsequently, the unclarified and
clarified feedstock were loaded. For clarified feedstock, the centrifugation was conducted for 20
minutes (4 ºC, 3000 rpm). Then the protein fractions were collected and assayed for protein
concentration and chitosanase activity. The dynamic binding capacity of the bed was checked
when the enzymatic activity in the column effluent reached 10% of the initial activity (U/U0 =
0.1). This methodology was accomplished to avoid the loss of the target product in the flow-
through.
The dynamic binding capacity, QB (U of enzyme absorbed per gram of settled adsorbent)
was calculated as follows:
𝑄𝐵 =𝑈0 (𝑉𝑓 − 𝑉𝑚)− ∫ 𝐶𝑑𝑉
𝑉𝑓𝑉𝑚
𝑚𝑎𝑑𝑠 Eq.2
U0 is the initial enzymatic activity (U.mL-1
), Vf is the final volume of the feed solution (mL), Vm
is the volume at 10% breakthrough (mL) and mads is the adsorbent mass (g).
Three additional experiments at superficial velocity of 100, 150 and 200 cm.h-
1(expansion degree of 1.2, 1.5 and 2.0, respectively) were performed using unclarified broth to
estimate the effect of the expansion degree in the chitosanase breakthrough behaviour.
Effect of pH and temperature on the enzyme activity
The optimum pH for purified chitosanase was studied by using soluble chitosan as
substrate with different pH values (3.0 – 10.0). For pH stability profile, the samples were
dialyzed against a 50mM buffer solution at various pH values (3.0 – 10.0) for 24 hours at 4 ºC.
The buffer systems were glycine-HCl (pH 3), acetate (pH 4.0 – 5.0), phosphate (pH 6.0 – 8.0)
and bicarbonate-carbonate (pH 9.0 – 10.0). After dialysis, the enzyme activity was determined
by the measurement of the residual activity at pH 6.0. The optimum temperature for the purified
chitosanase was determined by the enzymatic activity in different temperatures (30 to 80 ºC).The
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 56
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
stability profile was determined after pre-incubation of the samples for 60 minutes at various
temperatures (30 to 80 ºC) and then the residual activity was measured.
Effect of various chemicals and surfactants on the enzyme activity
The action of various chemical agents on chitosanolytic activity of purified enzyme was
investigated. The enzymes samples were pre-incubated with 5mM ions (Mg2+
, Cu2+
, Fe2+
, Ca2+
,
Zn2+
, Mn2+
and Ba2+
) in phosphate buffer 50 mM (pH7.0) at 4 ºC during 2 hours followed by
measurement of residual chitosanolytic activity. The enzyme sample incubated with buffer was
used as control.
Analytical methods
The chitosanase activity of the crude enzyme and chromatography samples were
measured by using 250 μL of enzyme sample incubated with 250 μL of 1% soluble chitosan (pH
6.0). The mixture was heated in a water bath for 30 minutes and the temperature was adjusted to
55 ºC. The reaction was interrupted by boiling the samples for 10 minutes [14]. The reducing
sugars were assayed in spectrophotometer (Thermo Spectronic) by the 3,5-Dinitrosalicylic acid
method, using D-glucosamine as standard [29]. A unit (U) of chitosanase was defined as the
amount of enzyme capable of generating 1.0 µmol of D-glucosamine per minute under the
conditions described above.
The protein content was determined using the Bicinchoninic Acid method with a BCA
Protein Assay Kit and Bovine Serum Albumin (BSA) as standard.
Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and zymogram
analysis
After the ion-exchange adsorption, the selected samples were subjected to electrophoresis
on a 12% polyacrylamide gel in the presence of SDS in order to estimate the purity of protein.
This samples were heat treated at 100 ºC for 5 minutes in according to the methodology
described by Laemmli [30]. Twenty microliters of each sample and the protein standards were
applied to the gel. Different protein standards were used: phosphorylase b (97 kDa), BSA (66
kDa), ovalbumin (45 kDa), carbonic anhydrase (30 kDa), soybean trypsin inhibitor (20.1 kDa),
and α-lactalbumin (14.4 kDa) (Bio-Rad Co., Richmond, EUA). After electrophoresis, the protein
bands on the gel were visualized by silver staining.
The protein samples were mixed with loading buffer without reducing agent and heating
for the zymogram analysis of chitosanase. In this case, electrophoresis were performed in a 12%
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 57
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
SDS–PAGE containing 0.1% chitosan and then placed on ice. After electrophoresis, the gel was
incubated in 50 mM sodium acetate buffer, pH 5.5, at 50 ºC for 1 h. The chitosanase activity on
the gel was visualised by staining the gel with 0.1% Congo Red dye, followed by de-staining
with 1.0 M NaCl [31].
RESULTS AND DISCUSSION
Identification of chitosanase-producing strain
Bacillus cereus C-01, a chitosanase-producing strain, was isolated from soil samples in
Natal/Brazil (S 05º52’11’’, Wo 35º13’08.4’’). The Bacillus C-01 strain showed the highest
chitosanase activity from 15 another strains isolated. This strain did not show positivity for any
microorganisms identified by PC33 Siemens Kit. The C-01 was selected and then maintained on
nutrient agar. This material was used throughout the study.
Strain C-01 is a gram-positive and grows in both aerobic and anaerobic environments.
The culture showed colonies with rounded, irregular border, average size of 4 mm and white
colour. According to the results of 16S rDNA nucleotide sequence (approximately 1.5kbp), the
strain C-01 showed identity with two strains exhibiting 100% similarity (Bacillus cereus and
Bacillus thuringiensis). Several works have showed difficulties to distinguish strains of B. cereus
and B. thuringiensis and have suggested that the two strains are considered as a single species
[32-36]. Therefore, the isolate was identified as B. cereus.
Production of chitosanase from Bacillus cereus C-01
The chitosanase activity was measured in the supernatant of strain B. cereus C-01 during
various cultivation times. After 12 hours of adaptation phase, exponential increase of protein
content and enzymatic activity was observed (Figure 1). The B. cereus C-01 started to secrete
significant levels of extracellular chitosanase at 6 hours and the maximal production achieved up
to 0.8 U/mL at 36 hours of cultivation (Figure 1). Thereafter, the chitosanase activity decreased
remarkably. This behaviour can be possibly be explained by the presence of the protease activity
in the medium and by the decline in the growth of microorganism. The production of enzymes
was closely related to the cell growth (noted by the increase in DNA concentration), i.e., the
product is growth-associated that is typical of a primary metabolism product. From Figure 1, it
also can be notice that the microorganism is in exponential growth phase between 8 and 30 hours
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 58
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
of the experiment. Results show in Figure 1 indicates that the production of chitosanase is cell-
growth dependent and B. cereus C-01 is a promising chitosanase producer.
Figure 1: Time-course of cell growth, chitosanase activity and protein content. C-01 was grown aerobically in broth
medium at 30 ºC for 72 hours: (■) Chitosanase activity, (○) total protein, (●) pH and (□) DNA content.
Other studies using Bacillus cereus for the production of chitosanase and chitinase also
reported maximum yield of enzyme after the first day of cultivation. The relationship between
chitosanase activity and cell growth was verified as well [16, 22, 37].
Hydrodynamic of the bed
Clarified and unclarified culture broths were used in order to obtain the characteristics of
the bed expansion (Figure 2). The Richard-Zaki equation was applied to determine the
hydrodynamic stability of the adsorbent bed during expansion (fluidization). The expansion
indexes were 4.76 and 4.03. The terminal velocities were 893.36 cm.h-1
and 807.70 cm.h-1
for
clarified and unclarified culture broth, respectively. A decrease in the value of terminal settling
velocity was motivated by an increase in the viscosity of the mobile phase. These results are in
agreement with other studies reported in literature [38, 39].
Some variables have influence on the expansion degree of the bed: liquid superficial
velocity, density of adsorbent particles and viscosity of feedstock [40]. The bed expansion
increases linearly with the superficial velocity. At a constant superficial velocity of 200 cm.h-1
,
the adsorbent was expanded evenly at a degree of 2.2 and 2.0 by using the clarified and
unclarified broth, respectively.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 59
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figure 2: Bed expansion height in function of superficial velocity of fluid. Unclarified (□) and clarified culture
broth (■).
It could be verified that expanded-bed height was higher in clarified culture broth. As
reported by Anspach (1999), the interactions of adsorbent particles with cell surfaces, DNA and
other substances may be the most limiting factors to a stable bed. These feedstock composition
leads aggregation and consequently bed instabilities and channeling [40]. Nevertheless, the small
differences between the expansion degrees indicate that the unclarified broth should be applied
directly to expand the bed. The use of unclarified culture has an important economic impact
because the biological sample can be used without any previous treatment.
Dynamic binding capacity
The adsorption experiments were conducted to evaluate the dynamic binding capacity of
chitosanase with clarified and unclarified broth. The breakthrough curve analysis is essential to
estimate the maximum loading amount of target protein. Usually, it is acceptable a loss of 10%
of target protein in the effluent [39]. Figure 3 presents the influence of culture broth on the shape
of breakthrough curves. The curves were similar for both systems, displaying little interaction
between biomass and bed. For unclarified broth, the equilibrium was achieved quickly.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 60
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figure 3: Effect of the presence of cells on the breakthrough curve behaviour of chitosanase into the resin
Streamline DEAE. Unclarified (□) and clarified culture broth (■).
The results also showed that the binding capacity of unclarified culture broth (0.3 U/g
adsorbent) was slightly lower compared to the clarified one (0.32 U/g adsorbent). This slightly
difference could suggest that the adsorptive capacity of streamline-DEAE is not hampered by the
presence of the cell, at least until U/U0 = 0.1. This supports the behaviour of the breakthrough
curves. Other authors have also reported weak influence of biomass on the adsorption capacity
and on the rupture curve [38, 41].
Three experiments at expansion degree of 1.2, 1.5 and 2.0 were performed using
unclarified culture broth. Figure 4 presents the dynamic behaviour of the process. For an
expansion degree of 2.0 the adsorption of chitosanase into the resin was very fast. Sixty
millilitres of culture broth was enough to saturated 70% of resin. The saturation condition
(U/U0=1.0) was achieved after 80mL of culture broth. For an expansion degree of 1.2 and 1.5 the
saturation condition was not achieved. Under the industrial point of view, it is more interesting to
work with a breakthrough up to 10% because the losses are reduced. In addition, for an
expansion degree of 2.0 and 1.5, a breakthrough of 10% was found after 20 and 30mL of culture
broth, respectively. High yields can be obtained by reduction of the operation time,
consequently, increase the process productivity [38].
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 61
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figure 4: Effect of expansion degree on the breakthrough curve behaviour of chitosanase into the resin Streamline
DEAE by using unclarified broth. Expansion degree of 1.2 (■), 1.5 (●) and 2.0 (▲).
Purification of chitosanase
An extracellular chitosanase was partially purified from the culture supernatant of B.
cereus C-01. The EBA chromatogram profile is depicted in Figure 5.
Figure 5: The elution profile of chitosanase after adsorption of broth culture on Streamline DEAE. Content of
protein (○) and enzyme activity (■).
From these results, it can be notice a larger peak of enzyme activity at elution compared
to the protein. As shown in Table 1, the elution steps of EBA were combined to give an overall
purification of about 3.6-fold for chitosanase. The overall activity yield of purified chitosanase
was 31%. The final amount of protein obtained was about 29 mg.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 62
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Table 1: Purification of the chitosanase from B. cereus C-01
Step Total
protein (mg) Total activity (U)
Specific
activity (U/mg)
Purification
Factor Yield (%)
Culture broth 121 63 0.52 1.0 100
Load 31 17 0.55 1.0 27
Washing 60 24 0.4 0.77 48
Streamline DEAE (Eluate 0.3
M NaCl) 9.0 8.0 0.9 1.75 13
Streamline DEAE (Eluate 0.7
M NaCl) 12 8.8 0.7 1.35 14
Streamline DEAE (Eluate 1.0
M NaCl)
8.0 2.2 0.27 0.52 4.0
By the analysis of SDS-Page, it was possible to identify two protein bands that were
concentrated by chromatographic process (Figure 6). The first one was eluted with 0.3 M NaCl
and the second with 0.7 M. Chitosanase activity of purified enzymes were demonstrated by
zymogram (Figure 6, lanes 6 and 7). A purification factor of 1.75 was obtained considering the
fraction of 0.3 M NaCl. These analyses represent a good result if one considers that just a single
purification step has been used. A purification factor of 1.61 was obtained for purification of
amylase using EBA [42]. Purification factors between 1.2 and 2.3 were obtained during the
purification study of antigen of hepatitis B by EBA [43].
Figure 6: SDS-PAGE analysis of the chitosanase from B. cereus C-01. Lanes: M- molecular markers; 1- culture
supernatant; 2- load; 3- washing; 4- fraction eluted with 0.3 M NaCl; 5- fraction eluted with 0.7 M NaCl; 6-
zymogram analysis for fraction eluted with 0.3 M NaCl; 7- zymogram analysis for fraction eluted with 0.7 M NaCl.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 63
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
The protein peak eluted with 0.3 M NaCl showed an apparent molecular mass of 33 kDa
while the other one eluted with 0.7 M NaCl showed approximately 44 kDa. The molecular mass
of these chitosanases were similar to another chitosanases produced by Bacillus strains, such as
B. cereus TKU030 (43 kDa) [16], B. cereus TKU022 (44 kDa) [17], B. cereus S1 (45 kDa) [44],
B. subtilis 168 (30 KDa) [31] and B. subtilis CH2 (29 kDa) [45]. The two distinct peaks of
chitosanases with different molecular mass can be related to the production of enzymes with
different mechanism of action (endo and exochitosanases). Other studies have also been reported
the production of two distinct forms of chitosanases [46, 47]. The use of single-step for enzyme
purification allowed the purification of a chitosanase with good qualitative results as well as
enzymatic activity.
Effect of pH and temperature
The fraction that exhibited higher purification factor (0.3 M NaCl) was used for the
characterization experiments. The effect of pH on the catalytic activity was studied by using
chitosan as substrate under the standard assay conditions. The pH activity profile of the purified
chitosanase exhibited maximum values at pH 5.5 (Figure 7). The optimum pH of the chitosanase
was similar to the others chitosanases already characterized; the most of them reported optimum
pH ranging from 4.0 to 6.0 [37, 48]. After 24 hours of incubation in different pH, it was observed
a plateau between pH 5.5 to 8.0.These results showed larger pH range stability compared to
others studies. For example, for this same period of incubation, it was found stability in a short
range of pH (6.0 to 7.0) for chitosanase purified from culture broth of Serratia sp. TKU016 [49].
Additionally, chitosanase produced by Janthinobacterium showed stability in a pH range from
5.0 to 7.0 [50]. Ultimately, it was verified that extreme pH reduces enzymatic activity over time.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 64
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figure 7: Effects of pH on the activity (■) and stability of chitosanase (●). The pH stability profile to the enzyme
was determined by measuring the residual enzyme activity at pH 6 after 24 hours of incubation in different pH
values (3.0 – 10.0) at 4 ºC.
The effect of temperature on chitosanase activity was also studied. The optimum
temperature for B. cereus C-01 purified chitosanase was 55 ºC (Figure 8).The enzyme solution
was incubated for 60 minutes at various temperatures and the residual activity was then
measured to examine the thermal stability. The chitosanase maintained its initial activity at a
range of temperature between 30 and 60 ºC. It was possible to keep 91% of its activity at 55 ºC.
The enzyme stability under its optimum temperature is extremely important for industrial
applications of enzymes. Temperature above 60 °C promoted reduction of enzyme activity, i.e.,
the enzyme denaturation occurs after this temperature.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 65
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figure 8: Effects of temperature on the activity (■) and stability of chitosanase (●). The enzymatic samples were
incubated for 60 minutes at temperature ranging from of 30 ºC to 80 ºC.
For two purified chitosanases synthesized by B. subtilis TKU007 [51] and B. cereus D-11
[37], it was retained only 60% of its original activity. This activity was obtained after 60 minutes
of exposure at temperatures near to the optimum of both enzymes. For recombinant chitosanase
from Penicillium sp. D-1, the exposition during 60 minutes at optimal temperature reduced 92%
of the enzyme activity compared to its initial activity [52]. Chitinase ChiA from Cellulomonas
uda showed maximum activity against colloidal chitin at 60 ºC, and higher temperatures resulted
in a significant loss of activity [53].
Effect of various ions on enzyme activity
The effects of some divalent ions on enzyme activity were examined for a further
characterization of the B. cereus C-01 chitosanase. The enzyme was pre-incubating with the
chemical compounds in 50 mM phosphate buffer (pH 7.0) at 4 ºC for 2 hours. The results are
shown in Figure 9.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 66
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figure 9: Effect of ions on chitosanase activity. The enzymatic samples were incubated at 4 ºC for 2 hours in the
presence of: Mg2+,
Cu2+
, Fe2+
, Ca2+
, Zn2+
, Mn2+
and Ba2+
.
The results show that the enzyme has been strongly activated by Mn2+
andthe activity was
increased 1.62-fold (Figure 9). It was also reported the activation of others chitosanases from B.
cereus strain by Mn2+
[19]. In studies with two chitosanases produced by Microbacterium sp., the
activity was increased 1.56-fold by the incubation with Mn2+
[47]. The activation by Mn2+
also
occurred for a chitosanase purified from fermentation broth of Gongronella sp. [54] and for an
endochitinase from Serratia plymuthica HRO-C48 [55]. It was also possible to observe a positive
influence of ions Ba+2
and Mg+2
. Nevertheless, the ions Cu+2
, Fe+2
and Zn+2
showed inhibitory
effect on chitosanase activity. This inhibitory effect was also reported by other authors [21, 56].
CONCLUSION
A study was carried out in order to evaluate the application of the EBA for enzyme
purification of a non-clarified broth. It was applied an anionic resin to purify a chitosanase from
B. cereus. A biochemical characterization of the enzyme was evaluated as well. The enzyme
binds to resin in the same extent using both clarified and unclarified culture broth (0.32 and 0.30
U/g adsorbent, respectively). The fraction recovered after the elution exhibited 31% of yield
increasing the specific activity 3.6-fold compared to initial one. Two protein fractions with
chitosanolytic activity eluted at different NaCl concentrations were recovered. A protein eluted
with 0.3 M NaCl and showed an apparent molecular mass of 33 kDa. Another eluted with 0.7 M
NaCl and had 44 kDa. This result suggests the existence of at least two different chitosanases.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 67
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
The purified chitosanase was stable at 30-60 ºC, pH 5.5 – 8.0 and showed the highest activity at
55 ºC, pH 5.5. The ions Cu+2
, Fe+2
and Zn+2
showed inhibitory effect on chitosanase activity. In
contrast, the enzyme was significantly activated by Mn2+
. The use of Streamline DEAE ionic
exchanger to expanded bed adsorption can be considered a good system for the recovery of
chitosanases from B. cereus C-01 since it reduces the purification steps. Reduction in costs and
time are of great importance for industrial processes, therefore the procedure described here has
high potential for large scale applications.
Acknowledgements
The authors thank the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) and the
Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) for the financial support.
REFERENCES
[1] J. Zhang, W. Xia, P. Liu, Q. Cheng, T. Tahirou, W. Gu, B. Li, Chitosan modification and
pharmaceutical/biomedical applications, Marine drugs, 8 (2010) 1962-1987.
[2] C.F. de Assis, L.S. Costa, R.F. Melo-Silveira, R.M. Oliveira, M.G. Pagnoncelli, H.A. Rocha,
G.R. de Macedo, E.S. Santos, Chitooligosaccharides antagonize the cytotoxic effect of
glucosamine, World journal of microbiology & biotechnology, 28 (2012) 1097-1105.
[3] S. Masuda, K. Azuma, S. Kurozumi, M. Kiyose, T. Osaki, T. Tsuka, N. Itoh, T. Imagawa, S.
Minami, K. Sato, Y. Okamoto, Anti-tumor properties of orally administered glucosamine and N-
acetyl-D-glucosamine oligomers in a mouse model, Carbohydrate polymers, 111 (2014) 783-
787.
[4] S.J. Wu, S.K. Pan, H.B. Wang, J.H. Wu, Preparation of chitooligosaccharides from cicada
slough and their antibacterial activity, International journal of biological macromolecules, 62
(2013) 348-351.
[5] I. Younes, S. Sellimi, M. Rinaudo, K. Jellouli, M. Nasri, Influence of acetylation degree and
molecular weight of homogeneous chitosans on antibacterial and antifungal activities,
International journal of food microbiology, 185 (2014) 57-63.
[6] D. Katiyar, B. Singh, A.M. Lall, C. Haldar, Efficacy of chitooligosaccharides for the
management of diabetes in alloxan induced mice: a correlative study with antihyperlipidemic and
antioxidative activity, European journal of pharmaceutical sciences : official journal of the
European Federation for Pharmaceutical Sciences, 44 (2011) 534-543.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 68
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
[7] G. Lodhi, Y.S. Kim, J.W. Hwang, S.K. Kim, Y.J. Jeon, J.Y. Je, C.B. Ahn, S.H. Moon, B.T.
Jeon, P.J. Park, Chitooligosaccharide and its derivatives: preparation and biological applications,
BioMed research international, 2014 (2014) 654913.
[8] B.B. Aam, E.B. Heggset, A.L. Norberg, M. Sorlie, K.M. Varum, V.G. Eijsink, Production of
chitooligosaccharides and their potential applications in medicine, Marine drugs, 8 (2010) 1482-
1517.
[9] V.K. Mourya, N.N. Inamdar, Y.M. Choudhari, Chitooligosaccharides: Synthesis,
characterization and applications, Polym. Sci. Ser. A, 53 (2011) 583-612.
[10] S.-K. Kim, N. Rajapakse, Enzymatic production and biological activities of chitosan
oligosaccharides (COS): A review, Carbohydrate polymers, 62 (2005) 357-368.
[11] J. Beck, M. Broniszewska, M. Schwienbacher, F. Ebel, Characterization of the Aspergillus
fumigatus chitosanase CsnB and evaluation of its potential use in serological diagnostics, Int J
Med Microbiol, 304 (2014) 696-702.
[12] Y.-M. Chang, Y.-J. Lee, J.-W. Liao, J.-K. Jhan, C.-T. Chang, Y.-C. Chung, In vitro and in
vivo safety evaluation of low molecular weight chitosans prepared by hydrolyzing crab shell
chitosans with bamboo shoots chitosanase, Food and Chemical Toxicology, 71 (2014) 10-16.
[13] H. Zhang, J. Fang, Y. Deng, Y. Zhao, Optimized production of Serratia marcescens B742
mutants for preparing chitin from shrimp shells powders, Int J Biol Macromol, 69 (2014) 319-
328.
[14] N.K. de Araujo, C.F. de Assis, E.S. Dos Santos, G.R. de Macedo, L.F. de Farias, H.
Arimateia, Jr., M. de Freitas Fernandes Pedrosa, M.G. Pagnoncelli, Production of enzymes by
Paenibacillus chitinolyticus and Paenibacillus ehimensis to obtain chitooligosaccharides, Appl
Biochem Biotechnol, 170 (2013) 292-300.
[15] D.-J. Seo, J.-H. Lee, Y.-S. Song, R.-D. Park, W.-J. Jung, Expression patterns of chitinase
and chitosanase produced from Bacillus cereus in suppression of phytopathogen, Microbial
Pathogenesis, 73 (2014) 31-36.
[16] T.W. Liang, Y.Y. Chen, P.S. Pan, S.L. Wang, Purification of chitinase/chitosanase from
Bacillus cereus and discovery of an enzyme inhibitor, Int J Biol Macromol, 63 (2014) 8-14.
[17] T.W. Liang, J.L. Hsieh, S.L. Wang, Production and purification of a protease, a chitosanase,
and chitin oligosaccharides by Bacillus cereus TKU022 fermentation, Carbohydr Res, 362
(2012) 38-46.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 69
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
[18] T.W. Liang, C.P. Liu, C. Wu, S.L. Wang, Applied development of crude enzyme from
Bacillus cereus in prebiotics and microbial community changes in soil, Carbohydr Polym, 92
(2013) 2141-2148.
[19] B.G. Goo, J.K. Park, Characterization of an alkalophilic extracellular chitosanase from
Bacillus cereus GU-02, J Biosci Bioeng, 117 (2014) 684-689.
[20] W.T. Chang, Y.C. Chen, C.L. Jao, Antifungal activity and enhancement of plant growth by
Bacillus cereus grown on shellfish chitin wastes, Bioresour Technol, 98 (2007) 1224-1230.
[21] A.D. Nguyen, C.-C. Huang, T.-W. Liang, V.B. Nguyen, P.-S. Pan, S.-L. Wang, Production
and purification of a fungal chitosanase and chitooligomers from Penicillium janthinellum D4
and discovery of the enzyme activators, Carbohydrate polymers, 108 (2014) 331-337.
[22] X. Jiang, D. Chen, L. Chen, G. Yang, S. Zou, Purification, characterization, and action
mode of a chitosanase from Streptomyces roseolus induced by chitin, Carbohydrate research,
355 (2012) 40-44.
[23] M. Tomita, A. Kikuchi, M. Kobayashi, M. Yamaguchi, S. Ifuku, S. Yamashoji, A. Ando, A.
Saito, Characterization of antifungal activity of the GH-46 subclass III chitosanase from Bacillus
circulans MH-K1, Antonie van Leeuwenhoek, 104 (2013) 737-748.
[24] V. Boeris, I. Balce, R.R. Vennapusa, M.A. Rodríguez, G. Picó, M.F. Lahore, Production,
recovery and purification of a recombinant β-galactosidase by expanded bed anion exchange
adsorption, Journal of Chromatography B, 900 (2012) 32-37.
[25] Q.Y. Du, D.Q. Lin, Q.L. Zhang, S.J. Yao, An integrated expanded bed adsorption process
for lactoferrin and immunoglobulin G purification from crude sweet whey, J Chromatogr B
Analyt Technol Biomed Life Sci, 947-948 (2014) 201-207.
[26] M.H. Khoodoo, M.I. Issack, Y. Jaufeerally-Fakim, Serotyping and RAPD profiles of
Salmonella enterica isolates from Mauritius, Lett Appl Microbiol, 35 (2002) 146-152.
[27] J.F. Richardson, W.N. Zaki, Sedimentation and fluidisation: Part I, Chemical Engineering
Research and Design, 75, Supplement (1997) S82-S100.
[28] F.C.d. Sousa Junior, M.R. Ferreira Vaz, C.E.d. Araújo Padilha, D.R. Arantes Martins, G.R.
de Macedo, E.S. dos Santos, Production, recovery, and purification of recombinant 503 antigen
of Leishmania infantum chagasi using expanded bed adsorption chromatography, BMC
Proceedings, 8 (2014) P194-P194.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 70
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
[29] G.L. Miller, Use of Dinitrosalicylic Acid Reagent for Determination of Reducing Sugar,
Analytical Chemistry, 31 (1959) 426-428.
[30] U.K. Laemmli, Cleavage of structural proteins during the assembly of the head of
bacteriophage T4, Nature, 227 (1970) 680-685.
[31] P. Pechsrichuang, K. Yoohat, M. Yamabhai, Production of recombinant Bacillus subtilis
chitosanase, suitable for biosynthesis of chitosan-oligosaccharides, Bioresour Technol, 127
(2013) 407-414.
[32] N.V. Punina, V.S. Zotov, A.L. Parkhomenko, T.U. Parkhomenko, A.F. Topunov, Genetic
Diversity of Bacillus thuringiensis from Different Geo-Ecological Regions of Ukraine by
Analyzing the 16S rRNA and gyrB Genes and by AP-PCR and saAFLP, Acta Naturae, 5 (2013)
90-100.
[33] M.L. Chen, H.Y. Tsen, Discrimination of Bacillus cereus and Bacillus thuringiensis with
16S rRNA and gyrB gene based PCR primers and sequencing of their annealing sites, J Appl
Microbiol, 92 (2002) 912-919.
[34] E. Helgason, O.A. Okstad, D.A. Caugant, H.A. Johansen, A. Fouet, M. Mock, I. Hegna,
A.B. Kolsto, Bacillus anthracis, Bacillus cereus, and Bacillus thuringiensis--one species on the
basis of genetic evidence, Appl Environ Microbiol, 66 (2000) 2627-2630.
[35] S.N. Bourque, J.R. Valero, M.C. Lavoie, R.C. Levesque, Comparative Analysis of the 16S
to 23S Ribosomal Intergenic Spacer Sequences of Bacillus thuringiensis Strains and Subspecies
and of Closely Related Species, Appl Environ Microbiol, 61 (1995) 2811.
[36] C. Ash, J.A. Farrow, M. Dorsch, E. Stackebrandt, M.D. Collins, Comparative analysis of
Bacillus anthracis, Bacillus cereus, and related species on the basis of reverse transcriptase
sequencing of 16S rRNA, Int J Syst Bacteriol, 41 (1991) 343-346.
[37] X.-A. Gao, W.-T. Ju, W.-J. Jung, R.-D. Park, Purification and characterization of
chitosanase from Bacillus cereus D-11, Carbohydrate Polymers, 72 (2008) 513-520.
[38] C.C. Moraes, M.A. Mazutti, F. Maugeri, S.J. Kalil, Modeling of ion exchange expanded-bed
chromatography for the purification of C-phycocyanin, J Chromatogr A, 1281 (2013) 73-78.
[39] F.C. Chong, W.S. Tan, D.R. Biak, T.C. Ling, B.T. Tey, Direct recovery of recombinant
nucleocapsid protein of Nipah virus from unclarified Escherichia coli homogenate using
hydrophobic interaction expanded bed adsorption chromatography, J Chromatogr A, 1217 (2010)
1293-1297.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 71
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
[40] F.B. Anspach, D. Curbelo, R. Hartmann, G. Garke, W.D. Deckwer, Expanded-bed
chromatography in primary protein purification, J Chromatogr A, 865 (1999) 129-144.
[41] F. Poulin, R. Jacquemart, G. De Crescenzo, M. Jolicoeur, R. Legros, A Study of the
interaction of HEK-293 cells with streamline chelating adsorbent in expanded bed operation,
Biotechnol Prog, 24 (2008) 279-282.
[42] A.L. Toledo, J.B. Severo, Jr., R.R. Souza, E.S. Campos, J.C. Santana, E.B. Tambourgi,
Purification by expanded bed adsorption and characterization of an alpha-amylases FORILASE
NTL from A. niger, J Chromatogr B Analyt Technol Biomed Life Sci, 846 (2007) 51-56.
[43] M.Y. Ng, W.S. Tan, N. Abdullah, T.C. Ling, B.T. Tey, Effect of different operating modes
and biomass concentrations on the recovery of recombinant hepatitis B core antigen from
thermal-treated unclarified Escherichia coli feedstock, J Biotechnol, 138 (2008) 74-79.
[44] M. Kurakake, S. Yo-u, K. Nakagawa, M. Sugihara, T. Komaki, Properties of chitosanase
from Bacillus cereus S1, Curr Microbiol, 40 (2000) 6-9.
[45] C. Oh, M. De Zoysa, D.H. Kang, Y. Lee, I. Whang, C. Nikapitiya, S.J. Heo, K.T. Yoon, A.
Affan, J. Lee, Isolation, purification, and enzymatic characterization of extracellular chitosanase
from marine bacterium Bacillus subtilis CH2, J Microbiol Biotechnol, 21 (2011) 1021-1025.
[46] S.K. Hsu, Y.C. Chung, C.T. Chang, H.Y. Sung, Purification and characterization of two
chitosanase isoforms from the sheaths of bamboo shoots, J Agric Food Chem, 60 (2012) 649-
657.
[47] Y. Sun, W. Liu, B. Han, J. Zhang, B. Liu, Purification and characterization of two types of
chitosanase from a Microbacterium sp, Biotechnol Lett, 28 (2006) 1393-1399.
[48] P.I. Kim, T.H. Kang, K.J. Chung, I.S. Kim, K.C. Chung, Purification of a constitutive
chitosanase produced by Bacillus sp. MET 1299 with cloning and expression of the gene, FEMS
Microbiol Lett, 240 (2004) 31-39.
[49] S.L. Wang, T.J. Chang, T.W. Liang, Conversion and degradation of shellfish wastes by
Serratia sp. TKU016 fermentation for the production of enzymes and bioactive materials,
Biodegradation, 21 (2010) 321-333.
[50] M.G. Johnsen, O.C. Hansen, P. Stougaard, Isolation, characterization and heterologous
expression of a novel chitosanase from Janthinobacterium sp. strain 4239, Microb Cell Fact, 9
(2010) 5.
Single-step purification of chitosanase from Bacillus cereus using expanded bed chromatography 72
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
[51] S.-L. Wang, P.-Y. Yeh, Purification and characterization of a chitosanase from a nattokinase
producing strain Bacillus subtilis TKU007, Process Biochemistry, 43 (2008) 132-138.
[52] X.-F. Zhu, H.-Q. Tan, C. Zhu, L. Liao, X.-Q. Zhang, M. Wu, Cloning and overexpression of
a new chitosanase gene from Penicillium sp. D-1, AMB Express, 2 (2012) 13-13.
[53] G. Reguera, S.B. Leschine, Biochemical and genetic characterization of ChiA, the major
enzyme component for the solubilization of chitin by Cellulomonas uda, Arch Microbiol, 180
(2003) 434-443.
[54] W. Zhou, H. Yuan, J. Wang, J. Yao, Production, purification and characterization of
chitosanase produced by Gongronella sp. JG, Lett Appl Microbiol, 46 (2008) 49-54.
[55] J. Frankowski, M. Lorito, F. Scala, R. Schmid, G. Berg, H. Bahl, Purification and properties
of two chitinolytic enzymes of Serratia plymuthica HRO-C48, Arch Microbiol, 176 (2001) 421-
426.
[56] S.-L. Wang, C.-P. Liu, T.-W. Liang, Fermented and enzymatic production of chitin/chitosan
oligosaccharides by extracellular chitinases from Bacillus cereus TKU027, Carbohydrate
Polymers, 90 (2012) 1305-1313.
Considerações Finais 74
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
6. CONSIDERAÇÕES FINAIS
Neste estudo foi descrita a purificação de uma quitosanase produzida pelo Bacilus cereus
utilizando a tecnologia de Adsorção em Leito Expandido. Inicialmente realizaram-se coletas de
solo para seleção de microrganismos produtores de quitosanases. Foram obtidas 15 cepas
bacterianas, as quais passaram por testes de patogenicidade e análises de produção de
quitosanases. Após a seleção e identificação do microrganismo escolhido – através de análises
morfológicas, teste de Gram e por métodos moleculares – um estudo para purificação da enzima
de interesse foi realizado. Foram estudadas as condições de operação da cromatografia em leito
expandido utilizando um Planejamento Composto Central. Além disso, foram avaliadas a
influência da biomassa no processo de purificação e a qualidade da amostra purificada.
Dentre as 15 cepas isoladas, aquela que apresentou maior potencial para hidrólise da
quitosana foi identificada como Bacillus cereus. Na otimização das condições de operação do
sistema cromatográfico para purificação da quitosanase produzida por esse microrganismo, foi
possível aumentar tanto o rendimento como o fator de purificação da molécula de interesse. Os
resultados do Planejamento Composto Central mostraram que o melhor rendimento global na
etapa de eluição foi de 47,27%. Enquanto que o melhor fator de purificação foi de 1,43. A
biomassa mostrou afetar minimamente o sistema: a enzima ligou-se a resina de forma
semelhante tanto com uso de caldo clarificado e como de não clarificado (0,32 e 0,30 U/g
adsorvente) e foi possível alcançar alturas de expansão semelhantes tanto pelo uso do caldo
clarificado como do não clarificado.
Nos estudos de purificação, foi possível observar duas bandas proteícas com atividade
quitosanolítica, eluidas com diferentes concentrações de NaCl. Aquela que apresentou maior
fator de purificação foi utilizada em testes qualitativos. As análises qualitativas do método
empregado mostraram uma considerável pureza da quitosanase tendo em vista que apenas uma
única operação foi empregada na purificação. Os íons Cu+2
, Fe+2
e Zn+2
mostraram efeito
inibitório para enzima. Em contraste, esta foi fortemente ativada por Mn2+
. A enzima purificada
apresentou massa molecular aparente de 33 kDa, temperatura e pH ótimos de hidrólise de 55 ºC
e 5,5, respectivamente. Adicionalmente, foi evidenciado estabilidade enzimática nas faixas de
pH 5,5 – 8,0 e temperatura 30 - 60 ºC. A estabilidade apresentada pelo extrato enzimático
mostrou que essa enzima tem uma promissora aplicação para produção de quitooligossacarídeos
Considerações Finais 75
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
bioativos. O uso da Adsorção em Leito Expandido também se mostrou eficaz como técnica de
purificação.
Estudos posteriores deverão ser realizados para avaliar a influência de diferentes
concentrações de biomassa sobre Adsorção em Leito Expandido e para otimizar a purificação da
segunda quitosanase.
Até o momento, com o desenvolvimento deste estudo foi possível gerar três produções
científicas, três trabalhos foram apresentados em congressos internacionais e 04 em congressos
regionais. Além disso, cinco alunos de graduação atuaram neste projeto contribuindo assim para
sua formação acadêmica.
Apêndice 77
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
7. APÊNDICE
A seguir será apresentado um estudo matemático sobre o processo de purificação
empregado nesse trabalho de doutorado. Este estudo matemático foi concebido em parceria com
um aluno de pós-graduação do Programa de Pós-Graduação em Engenharia Química.
Apêndice 78
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Modelagem e simulação da adsorção de quitosanases produzidas por Bacillus cereus em
uma coluna operada em leito expandido
Araújo, Nathália Kelly de1; Padilha, Carlos Eduardo de Araújo
1; Souza, Domingos Fabiano de Santana
1; Oliveira,
Jackson Araújo de1; Macedo, Gorete Ribeiro de
1; Santos, Everaldo Silvino dos
1
1Laboratório de Engenharia Bioquímica, Departamento de Engenharia Química,Universidade Federal do Rio Grande
do Norte (UFRN), Natal-RN, Brasil.
Abstract
Neste estudo um modelo matemático foi elaborado para descrever as etapas de carga, lavagem e
eluição de uma coluna de troca iônica operada em leito expandido durante a purificação de
quitosanases produzidas por Bacillus cereus. A estratégia de estimação híbrida composta pelos
métodos particle swarm optimization (PSO) e Gauss-Newton foi adotada para estimar os
parâmetros do modelo. A sensibilidade paramétrica foi aplicada para realizar a triagem dos
parâmetros relevantes ao modelo e reduzir o esforço do método Gauss-Newton. Através dos
testes 2 e das médias dos erros quadráticos foi observado que o desempenho do modelo com os
parâmetros re-estimados foi superior àquele obtido apenas com o método de Gauss-Newton. A
aplicação do modelo validado sob as condições operacionais ótimas permitiram que fosse
alcançado o máximo de 15.03 % de rendimento na eluição 700 mM de NaCl.
Keywords: Modeling, Expanded Bed Adsorption, Chitosanases, Particle Swarm Optimization,
Gauss-Newton, Optimization
1. Introdução
Pesquisas sobre quitosanases têm recebido grande atenção devido a sua ampla aplicação
em vários campos [1]. Entre essas aplicações, inclui-se a preparação de quitoligossacarídeos
bioativos [2-3], de agentes de biocontrole para aumentar a resistência de plantas contra
patógenos fúngicos [4], mediar a entrega de gene [5] e a bioconversão de resíduos quitinosos
marinhos [2]. Contudo o uso direto do caldo fermentado microbiano contendo atividade
quitosanolítica não é recomendável, uma vez que nele podem existir metabólitos secundários
indesejáveis e proteases. Por outro lado, a necessidade de etapas de purificação pode aumentar
substancialmente o custo total de produção. Assim incentivos têm sido feitos para intensificação
e integração das técnicas de downstream processing na ordem de assegurar a viabilidade
econômica do processo [6-9].
Apêndice 79
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
A adsorção em leito expandido (ALE) é uma técnica cromatográfica que combina
remoção de insolúveis, concentração e purificação em apenas um passo [10-12]. Nela, a
aplicação de um fluxo ascendente sobre um leito de partículas adsorventes permite não só a
passagem de material particulado bem como a adsorção da molécula-alvo [13-14]. A distribuição
de partículas ao longo da coluna cromatográfica ocorre pelas variações de tamanho e densidade
das partículas, o que torna a análise da cinética da ALE uma tarefa complexa [15].
Uma ferramenta útil para compreender os complexos mecanismos envolvidos na
operação da coluna de adsorção em leito expandido, bem como a otimização de condições
operacionais é a utilização da modelagem matemática [15,8]. A troca iônica (IEX) é a
modalidade do processo ALE com maior número de trabalhos de modelagem e eles abordam as
etapas carga, lavagem e eluição. Nesta última etapa faz-se necessário incorporar isotermas que
levem em consideração a atuação do sal na adsorção, das quais se destaca a Steric Mass Action
(SMA). A isoterma SMA tem mostrado resultados promissores na descrição do comportamento
da adsorção de uma única proteína [16-17] ou simples combinações de proteínas [18-19].
Contudo, para sistemas complexos como caldo fermentado com células e/ou quando não se pode
realizar ensaios prévios com a proteína-alvo pura, o seu uso é inviável. Para contornar estes
problemas uma alternativa simples seria a inclusão de um termo exponencial associado à
concentração de sal no modelo de isoterma de Langmuir como visto em Antia and Horváth
(1989) [20] e Chen and Sun (2003) [21].
Neste contexto, o presente trabalho propõe a modificação do modelo matemático de
sistemas cromatográficos para permitir a descrição das etapas carga, lavagem e eluição do
processo ALE durante a purificação de quitosanase a partir de extrato bruto com células. A
abordagem híbrida foi usada para estimar os parâmetros do modelo e a análise de medidas
estatísticas foi realizada para avaliar o desempenho do modelo. Com o modelo enfim validado,
uma rotina de otimização foi usada para maximizar a função rendimento pela manipulação das
condições operacionais do processo ALE.
2. Materiais e Métodos
2.1. Microrganismo
Apêndice 80
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Uma bactéria identificada como Bacillus cereus foi isolada de amostras de solo em
Natal/Brasil (S 05º52’11’’, Wo 35º13’08.4’’). Diluições seriadas de amostras de solo foram
inoculadas em placas de petri contendo peptona (6,0 gL-1
), quitosana (2,0 gL-1
), sulfato de
magnésio (0,5 gL-1
), fosfato dibásico de potássio (1,0 gL-1
) e ágar (15 gL-1
), e incubadas a 30ºC
por dois dias. Colônias foram isoladas, testadas quanto a atividade quitosanolítica e selecionadas
para análises taxonômica, coloração por gram e teste de patogenicidade usando o Kit Siemens
PC33. Para uma identificação mais profunda, reação em cadeia da polimerase (PCR) foi
realizada para amplificação do gene codificador do rRNA 16S. Foram utilizados os iniciadores,
direto e reverso, 27F (5’-AGA GTT TGA TCC TGG CTC AG-3’) e 1525R (5’-AAG GAG GTG
ATC CAG CC-3’), respectivamente. Os produtos do PCR foram analisados por eletroforese em
gel de agarose e, depois, purificados, quantificados e usados para sequenciamento. Quatro
reações de sequenciamento foram realizadas usando os primers 518F (5’-CCA GCA GCC
GCG GTA ATA CG-3’), 800R (5’-TAC CAG GGT ATC TAA TCC-3’) e 1492R (5’-TAC
GGY TAC CTT GTTA CGA CTT-3’). A sequência de nucleotídeos do 16S rRNA da amostra
foi determinada por ABI 3730 DNA Sequencer (Applied Biosystems, USA) e comparada com
sequências de 16S rRNA disponíveis no NCBI BLAST.
2.2. Produção das quitosanases
Alíquotas de células, estocadas em ágar nutriente, foram transferidas para 50 mL meio de
pré-cultivo dispensado em Erlenmeyer (250 mL), e então incubados a 30º C, 120 rpm, por 30
horas. O meio de pré-cultivo consistiu de: peptona (6,0 gL-1
), quitosana (2,0 gL-1
), sulfato de
magnésio (0,5 gL-1
) e fosfato dibásico de potássio (1,0 gL-1
). Este foi, em seguida, inoculado
assepticamente a um nível de 10% (v/v) em Erlenmeyer de 250 mL contendo 50 mL do mesmo
meio [3]. Os frascos foram então colocados num agitador rotativo a 120 rpm durante 24 horas,
30° C (Tecnal, TE421). Amostras deste cultivo foram usadas para o ensaio de purificação.
2.3. Ensaios de adsorção em leito expandido
O adsorvente de troca aniônica Streamline DEAE (GE Healthcare, Uppsala, Sweden) foi
usado nos experimentos. Microesferas de vidro foram utilizadas na base da coluna para
acomodar o leito adsorvente e permitir a passagem dos sólidos particulados. O fluído foi injetado
na coluna usando bomba peristáltica (Perimax 12, Spetec). Foram realizados 5 ensaios de acordo
Apêndice 81
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
com a Tabela 1. O correto alinhamento vertical da coluna foi assegurado em todos os
experimentos e todos os experimentos foram realizados à temperatura ambiente.
A coluna, com diferente alturas de leito sedimentado, foi equilibrada com tampão Tris-
HCl, 50 mM, pH 8,5 (tampão A) para que fosse alcançada a altura uma estável, onde H/H0=1,5.
O caldo fermentado com células foi então aplicado (etapa de carga) a uma velocidade superficial
variável (de acordo com a tabela 1), seguido de lavagem com tampão A (150 mL). A eluição foi
realizada por gradiente salino passo a passo com tampão Tris-HCl, pH 8,5 contendo 0,3 M
(tampão B), 0,7 M (tampão C) e 1,0 M (tampão D) de NaCl. As etapas de lavagem e eluição
conduzidas a uma velocidade superficial de 100 cm.h-1
. Em todas as etapas de purificação, várias
frações foram coletadas para realização de ensaio enzimático.
Tabela 1. Condições operacionais dos ensaios de ALE para recuperação de quitosanase
Ensaio Altura do
leito fixo (cm)
Altura do leito
distribuidor
(cm)
Velocidade
superficial
(cm.h-1
)
Atividade enzimática do
extrato bruto (U.mL-1
)
1 8.00 2.00 100.00 0.440
2 4.00 2.00 200.00 0.430
3 8.00 6.00 100.00 0.210
4 8.00 6.00 200.00 0.298
5*
6.00 4.00 150.00 0.298
* - O ensaio 5 foi usado como validação do modelo matemático
2.4. Determinação da atividade enzimática
A atividade enzimática do caldo bruto e de amostras cromatográficas foram mensuradas
pela incubação de 250 μL da amostra enzimática com 250 μL de quitosana 1% (pH 6,0). A
mistura foi incubada em banho-maria por 30 minutos e a temperatura ajustada para 55ºC. A
reação foi interrompida por fervura durante 10 minutos (De Araújo et al., 2013). A formação de
açúcares redutores foi analisada pelo método do ácido dinitro salicilico, usando D-glucosamina
Apêndice 82
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
como padrão [22]. Uma unidade (U) de quitosanase foi definida como a quantidade de enzima
capaz de gerar 1 µmol de D-glucosamina por minuto nas condições descritas acima.
3. Formulação do Modelo
A elaboração do modelo matemático que descreve todo o ciclo de operação de uma
coluna de ALE voltada para purificação da quitosanase em uma resina de troca iônica foi
baseada nas seguintes hipóteses:
i. As partículas adsorventes foram consideradas como esferas de densidade uniforme e
grupos funcionais igualmente distribuídos na superfície. Variações axiais do raio das
partículas adsorventes (Rp) e da porosidade do leito (ε) foram assumidas conforme Li et
al. (2005) [23].
ii. O comportamento hidrodinâmico da fase fluida pode ser descrito pelo modelo de
dispersão axial [24-25].
iii. A adsorção do componente quitosanase (1) ocorreu apenas na superfície do adsorvente,
logo não foi considerada a difusão interna.
iv. A interação entre biomassa e leito adsorvente foi negligenciada.
v. O comportamento reológico da fase fluida é diferente em cada etapa do processo de ALE.
Para descrever todo o ciclo de operação ALE foi necessário incluir o componente sal (2)
para a etapa de eluição e foi assumido que ele não interage com o adsorvente.
vi. A isoterma de Langmuir modificada foi usada para descrever o equilíbrio de adsorção da
quitosanase nas três etapas do processo de ALE.
O balanço de massa do componente i na fase fluida pode ser expresso como
2, ,
, 2
3 1p
f i i i r Ri i i
ax ip
k z C CC C CUD
t z z z R zz
(1)
onde Dax,i é o coeficiente de dispersão axial do componente i (cm2.s
-1), kf,i é o coeficiente de
transferência de massa no filme líquido do componente i (cm.s-1
), U é a velocidade superficial
(cm.s-1
), t é o tempo (s), iC e ,p
i r RC é a concentração do componente i na fase fluida e na
superfície da partícula adsorvente, respectivamente.
Apêndice 83
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
As condições iniciais e condições de contorno da etapa carga são:
CI : 0, ,0 0it C z (1a)
0CC : 0, 0,
, 0
i i
i
t z C C
Cz H
z
(1b)
Assumindo que todas as resistências à transferência de massa se resumem a razão entre a
constante de adsorção (b1) e a constante de dessorção (b2), o balanço de massa da quitosanase na
fase sólida pode ser simplificado como é visto a seguir:
1 1 max 2
qb C q q b q
t
(2)
onde q é a concentração de quitosanase adsorvida pela resina e qmax é a capacidade máxima de
adsorção de quitosanase na resina. A condição inicial da etapa carga é dada por:
CI : 0, ,0 0t q z (2a)
De maneira a promover a recuperação de quitosanases na etapa eluição, o termo qmax foi
considerado como inversamente proporcional à concentração de sal na fase fluida em um dado
estágio da coluna, conforme a Equação 3.
'max max 1 2expq q k C (3)
Assumindo que a taxa de adsorção na resina é equivalente ao decréscimo de sua concentração na
fase fluida, o termo ,p
i r RC pode ser fornecido através de manipulações matemáticas entre as
Equações 1 e 2, resultando na Equação 4. Como o componente sal não possui equação de
balanço no sólido teremos 2, 2p
r RC C , de modo que o terceiro termo da Equação 1 torna-se
nulo.
Apêndice 84
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
21
, 11,
1max
, 1
1
3
11
3
p
p
fr R
p
f
zR z b qC
k zC
zb R zq q
k z
(4)
As Equações 1-4 também podem ser usadas para descrever as etapas lavagem ( 10 0C ,
20 0C ) e eluição ( 10 0C , 20 0C ), exceto nas duas condições iniciais dadas pelas Equações
1a e 2a, que devem corresponder ao término das etapas carga e lavagem, respectivamente. Cada
etapa possui um conjunto próprio de parâmetros para a quitosanase, porém os valores de qmax, b1
e b2 foram fixados, o que totaliza 11 parâmetros. Os subscritos l, w e e foram usados para
informar sobre os parâmetros que pertencem às etapas carga, lavagem e eluição,
respectivamente.
Para a integração numérica do modelo contemplando todas as etapas, foi aplicado o
Método das Linhas [26]. Neste modelo a altura da coluna cromatográfica (coordenada espacial z)
foi discretizada em n elementos utilizando o método de diferenças finitas centrais. Em cada
elemento, a derivada parcial no tempo, foi aproximada por uma derivada ordinária. O sistema de
equações diferenciais ordinárias discretizados nos n elementos foram resolvidos utilizando a
subrotina numérica DASSL [27].
3.5. Estimação de parâmetros do modelo
O enxame de partículas (PSO) é um algoritmo de busca heurística baseado na
movimentação gregária de animais. Nele, a estimação é realizada por uma população de
partículas que se movimenta no espaço multidimensional trocando entre si informações sobre a
função objetivo [28-30]. A função objetivo (FO) a ser minimizada é do tipo mínimos quadrados
ponderados, que estabelece a diferença entre os valores experimentais ( expiC ) e calculados ( calc
iC
) associada ao erro de medição ( i ).
2
exp calc
21
N ii
i i
C CFO
(5)
Apêndice 85
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Neste trabalho foram usados 20 partículas e 20 iterações com valores dos parâmetros
inicial, cognitivo e social fixados em 0.7, 1.0 e 1.0, respectivamente. Os intervalos de busca dos
parâmetros do modelo foram: Dax,1l, Dax,1w, Dax,2 [5 x 10-3
,0.75] cm2.s
-1, kf,1l, kf,1w [5 x 10
-
3,0.75] cm.s
-1, qmax[0.25,1] U.g
-1, b1[10
-2,0.5] g.U
-1.s
-1, b2[5 x 10
-4,5 x 10
-2] s
-1, Dax,1e[5
x 10-5
,2.5 x 10-3
] cm2.s
-1, kf,1e[5 x 10
-5,5 x 10
-2] cm.s
-1, k1[5 x 10
-3,0.75] L.mmol
-1. Como o
ciclo de operação ALE é formado por três etapas onde a seguinte depende da anterior, pensou-se
a princípio em estimar primeiramente os parâmetros referentes à carga seguidos dos parâmetros
da lavagem e da eluição. Entretanto, esta estratégia não obteve resultados satisfatórios
(resultados não mostrados neste trabalho), então a alternativa foi a estimação simultânea de todos
os parâmetros do modelo.
Com o conjunto de parâmetros já calibrado pelo algoritmo PSO e finalizada a
sensibilidade paramétrica, alguns parâmetros foram re-estimados pelo método Gauss-Newton. O
pacote computacional Estima desenvolvido na COPPE-UFRJ foi usado para este propósito,
buscando minimizar a função objetivo descrita na Equação 5. Através dele foi possível também
obter a matriz de covariância e desvios-padrão dos parâmetros do modelo.
3.7. Otimização do rendimento da adsorção em leito expandido
A principal vantagem da modelagem matemática é a possibilidade de simular o processo
em condições experimentais não testadas baseando-se no conjunto de parâmetros estimados [29].
Assim, nesta etapa foram avaliados os efeitos da concentração inicial da carga, altura do leito
fixo, altura do distribuidor e a velocidade superficial sobre a recuperação do adsorbato. A função
objetivo escolhida a ser maximizada foi o percentual de rendimento na eluição a 700 mM de
NaCl descrito a seguir:
2
1
1
10 carga
Yield (%) 100
e
e
t
t
C dt F
C V
(6)
Apêndice 86
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Onde 2
1
1
e
e
t
t
C dt representa a quantidade de quitosanase recuperada a 700 mM de NaCl, F é a
vazão volumétrica e cargaV é o volume de extrato bruto contendo quitosanase aplicado na carga.
A rotina DBCONF, baseada no algoritmo quasi-Newton, foi usada para buscar o maximizador
dentro do espaço delimitado pelas condições empregadas na calibração dos parâmetros.
4. Resultados e Discussões
No caso de sistemas super parametrizados, como no atual trabalho, o modelo pode
carregar parâmetros praticamente não-identificáveis, o que dificulta o uso de um método baseado
em gradientes [31]. Dessa forma, partiu-se para uma estratégia de estimação de parâmetros
híbrida, tendo como chute inicial do método determinístico o conjunto de parâmetros estimados
pelo método heurístico. Por suas características vantajosas, o algoritmo PSO foi escolhido para
realizar a estimação dos 11 parâmetros do modelo com os dados experimentais provenientes dos
Ensaios 1, 2, 3 e 4. Os valores estimados pelo algoritmo PSO são mostrados na primeira coluna
da Tabela 2.
Tabela 2. Parâmetros do modelo estimados pelo algoritmo PSO e pelo pacote computacional
baseado no algoritmo Gauss-Newton.
Parameter
Estimated values
PSO Algorithm Gauss-Newton algorithm
Dax,1 l (cm2.s
-1) 1.065 x 10
-2 1.144 x 10
-2 ± 1.441 x 10
-3
kf, 1l (cm.s-1
) 0.430
0.430
qmax (U.g-1
) 0.756
0.645 ± 6.376 x 10-2
b1 (g.U-1
.s-1
) 3.134 x 10-2
3.345 x 10-2
± 4.637 x 10-3
b2 (s-1
) 1.000 x 10-3
4.091 x 10-4
± 1.749 x 10-4
Dax, 1w (cm2.s
-1) 3.953 x 10
-2 3.814 x 10
-2 ± 5.058 x 10
-3
Apêndice 87
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
kf, 1w (cm.s-1
) 0.474
0.474
Dax, 1e (cm2.s
-1) 1.710 x 10
-3 1.710 x 10
-3
kf, 1e (cm.s-1
) 3.995 x 10-3
3.995 x 10-3
Dax, 2 (cm2.s
-1) 6.291 x 10
-4 6.291 x 10
-4
k1 (L.mmol-1
) 0.488 0.488
Uma análise de sensibilidade paramétrica foi realizada sobre o conjunto calibrado pelo
algoritmo PSO seguindo a metodologia de Brun et al. (2001) [31] e Prunescu and Sin (2013)
[32]. A medida de sensibilidade paramétrica msqr foi obtida para cada etapa do processo como
loadingmsqr
, washingmsqr
, elutionmsqr
, representando as etapas carga, lavagem e eluição, respectivamente.
Também foi realizada uma avaliação global dada pelo indicador totalmsqr
e um threshold
selecionado. Os parâmetros estão posicionados de acordo as etapas do processo ALE e estão
mostrados na Figura 1.
Os resultados de sensibilidade paramétrica indicaram que o coeficiente de dispersão axial
,1ax lD a capacidade máxima de adsorção, maxq , e as constantes de adsorção 1b e
dessorção 2b da quitosanase na carga, bem como o coeficiente de dispersão axial da
quitosanase na lavagem ,1ax wD foram os parâmetros que causaram maior impacto na resposta
do modelo. As perturbações no coeficiente de dispersão axial da quitosanase na eluição ,1ax eD
, nos coeficientes de transferência de massa no filme líquido da quitosanase nas três etapas
,1 ,1 ,1, , f l f w f ek k k , no coeficiente de dispersão axial do sal ,2axD e no termo de
deslocamento da proteína pela presença de sal 1k pouco afetaram a medida totalmsqr
, sendo
considerados não-relevantes a nível de 0.15 e por isso foram fixados. Os parâmetros relevantes
podem ser expressos na forma vetorial como é visto a seguir:
Apêndice 88
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
,1 max 1 2 ,1 T
S ax l ax wD q b b D (7)
Os parâmetros s foram re-estimados sobre o mesmo conjunto de dados para se obter
melhor ajuste. A estratégia de estimação em um único passo também foi mantida. Os parâmetros
re-estimados e seus respectivos desvios padrões são mostrados na segunda coluna da Tabela 2.
A)
B)
Apêndice 89
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
C)
D)
Figura 1. Os três primeiros gráficos mostram msqr para a etapa carga ( loading
msqr ) (a), etapa
lavagem ( washingmsqr
) (b) e etapa eluição ( elutionmsqr
) (c). O gráfico de fundo mostra a medida de
sensibilidade total totalmsqr
com respeito aos parâmetros do modelo k e a threshold delimita os
parâmetros relevantes ao modelo (d).
Na Figura 5 estão dispostos os perfis simulados de concentração de quitosanase na saída
da coluna de ALE em diferentes condições operacionais com os parâmetros estimados do
Apêndice 90
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
algoritmo PSO e do algoritmo Gauss-Newton. A diferença de valores nos cinco termos de s
alterou significativamente o comportamento do modelo nas três etapas. As curvas de ruptura
geradas com os parâmetros do PSO estão posicionadas mais a direita e apresentaram o formato S
característico, enquanto que as curvas de ruptura com os parâmetros re-estimados saturaram
antecipadamente e atingiram maiores valores de concentração na saída. Na lavagem a queda da
concentração de quitosanase foi mais branda com os parâmetros do PSO do que com os
parâmetros re-estimados. A inclusão do termo exponencial na equação de Langmuir realmente
provocou a subida na concentração de quitosanase pela injeção da solução eluente, assim como
ocorreu experimentalmente. Na eluição os picos simulados com os parâmetros PSO surgiram tão
logo foi injetada a solução eluente a 700 mM de NaCl, enquanto que os picos com os parâmetros
re-estimados foram mais largos e surgiram posteriormente no cromatograma. Independente do
conjunto paramétrico usado, é de se destacar um grande desvio entre os resultados da simulação
e os dados experimentais na etapa de eluição a 300 mM de NaCl, onde foi registrado um
pequeno degrau de concentração de quitosanase na saída da coluna. Isto pode ser atribuído ao
efeito do decréscimo da porosidade do leito pela mudança do regime expandido na lavagem para
o regime compactado na eluição, causando o aumento da dessorção das quitosanases nas
simulações do que observado experimentalmente.
Apêndice 92
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figura 2. Perfis dos cromatogramas da adsorção de quitosanases em uma coluna operada em
leito expandido. A - Ensaio 1; B - Ensaio 2; C - Ensaio 3; D - Ensaio 4; E - Ensaio 5. (■) são os
dados experimentais. As linhas sólidas são as respostas da simulação com os parâmetros do PSO.
As linhas tracejadas são as respostas da simulação com os parâmetros re-estimados.
A qualidade do ajuste das curvas simuladas em relação aos dados experimentais foi
avaliada pelo teste 2 (Eq. 8) e pela medida estatística mean square error (MSE) (Eq. 9).
Apêndice 93
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
2
exp calc
2 1calc
N
iii
i
C C
C
(8)
2
exp calc
1
N
iii
C C
MSEN
(9)
A Tabela 3 mostra os valores de MSE e 2 obtidos nos ensaios de calibração e validação
para os conjuntos de paramétricos PSO e Gauss-Newton. Em relação aos ensaios responsáveis
pela calibração dos parâmetros foi observado que o conjunto de parâmetros PSO gerou valores
baixos de MSE e 2 , tendo a hipótese de igualdade aceita nos quatros ensaios a nível de 95 %
de confiança e grau de liberdade igual a 41 (2 56.94c ). A re-estimação dos parâmetros s
apenas permitiu aumentar a qualidade global de ajuste, muito embora tenha ocorrido o aumento
do valor de MSE na simulação da corrida 2. Ademais, bons resultados foram obtidos na
simulação do Ensaio 5, mesmo ele não participando da estimação dos parâmetros do modelo. A
re-estimação dos parâmetros por Gauss-Newton reduziu o valor de MSE de 9.634 x 10-4
para e
8.671 x 10-4
e o valor de 2 de 0.90 para 0.88, mostrando que a estimação híbrida é um caminho
interessante para estimação de parâmetros para modelos general rate.
Apêndice 94
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Tabela 3. Valores das medidas estatísticas 2 e MSE obtidos da simulação do modelo com o
conjunto de parâmetros do algoritmo PSO e da re-estimação.
Parameter set Run 1 Run 2 Run 3 Run 4 Run 5
Without re-
estimation
2
3.98
(Significant)
9.77
(Significant)
0.97
(Significant)
4.19
(Significant)
0.90
(Significant)
MSE 2.560 x 10-3
8.364 x 10-4
9.215 x 10-4
3.258 x 10-3
9.634 x 10-4
With re-
estimation
2
1.49
(Significant)
3.68
(Significant)
0.33
(Significant)
0.59
(Significant)
0.88
(Significant)
MSE 1.800 x 10-3
1.699 x 10-3
2.327 x 10-4
9.497 x 10-4
8.671 x 10-4
Com o modelo já validado, ele foi usado para a otimização das condições operacionais da
ALE tendo como função objetivo o rendimento na eluição 700 mM de NaCl descrito na Equação
11. Neste procedimento foram preservados os volumes usados na carga, lavagem e eluição, o
fluxo volumétrico na eluição e as concentrações de sal nas soluções eluentes. A solução da
otimização revelou que as condições operacionais 0 8H cm, 2disH cm, 100u cm/h e
10 0.21C U/mL permitiram que o rendimento na eluição 700 mM de NaCl alcançasse o
máximo de 15.03 %. Este valor é superior ao rendimento obtido na mesma etapa no Ensaio 4,
12.41 %, o maior alcançado nos experimentos. A Figura 3 mostra o comportamento da
concentração de quitosanase na saída da coluna durante o processo ALE nas condições
operacionais ótimas.
Apêndice 95
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Figura 3. Perfil simulado do cromatograma de adsorção de quitosanases em uma coluna operada
em leito expandido sob condições ótimas.
5. Conclusões
Neste trabalho buscou-se elaborar um modelo matemático que descreva o comportamento
da concentração do adsorbato durante as etapas carga, lavagem e eluição na purificação de
quitosanases por ALE. A abordagem híbrida, composta pelo algoritmo PSO e pelo algoritmo
Gauss-Newton, foi usada para a estimação dos parâmetros do modelo e a escolha dos parâmetros
relevantes foi feita através do método de sensibilidade paramétrica. O desempenho do modelo
matemático melhorou com a re-estimação dos parâmetros ,1ax lD , maxq , 1b , 2b e ,1ax wD ,
obtendo baixos valores de MSE e 2 mesmo para a corrida de validação. Dentro dos limites da
calibração, as condições ótimas foram 0 8H cm, 2disH cm, 100u cm/h e 10 0.21C
U/mL, que permitiram o rendimento máximo de 15.03 % na eluição 700 mM.
Apêndice 96
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
Agradecimentos
Os autores agradecem ao CNPq e Capes pelo suporte financeiro.
Referências
[1] Thadathil N, Velappan SP. Recent developments in chitosanase research and its biotechnological
applications: A review. Food Chemistry 2014;150:392-399.
[2] Wang SL, Tseng WN, Liang TW. Biodegradation of shellfish wastes and production of chitosanases
by a squid pen-assimilating bacterium, Acinetobacter calcoaceticus TKU024. Biodegradation
2011;22:939-948.
[3] Araujo NK, Assis CF, Santos ES, Macedo GR, Farias LF, Arimateia H, Jr., Freitas Fernandes Pedrosa
M, Pagnoncelli MG. Production of enzymes by Paenibacillus chitinolyticus and Paenibacillus
ehimensis to obtain chitooligosaccharides. Applied biochemistry and biotechnology
2013;170:292-300.
[4] Hsu SK, Chung YC, Chang CT, Sung HY. Purification and characterization of two chitosanase
isoforms from the sheaths of bamboo shoots. Journal of agricultural and food chemistry
2012;60:649-657.
[5] Almalik A, Day PJ, Tirelli N. HA-coated chitosan nanoparticles for CD44-mediated nucleic acid
delivery. Macromolecular bioscience 2013;13:1671-1680.
[6] Fee CJ. Economics of wash strategies for expanded bed adsorption of proteins from milk with
buoyancy-induced mixing. Chemical Engineering and Processing: Process Intensification
2001;40:329-334.
[7] Santos ES, Guirardello R, Franco TT. Preparative chromatography of xylanase using expanded bed
adsorption. Journal of Chromatography A 2002;944:217-224.
[8] Moraes CC, Mazutti MA, Rodrigues MI, Filho FM, Kalil SJ. Mathematical modeling and simulation
of inulinase adsorption in expanded bed column. Journal of chromatography A 2009;1216:4395-
4401.
[9] Vicente FA, Malpiedi LP, e Silva FA, Pessoa Jr A, Coutinho JAP, Ventura SPM. Design of novel
aqueous micellar two-phase systems using ionic liquids as co-surfactants for the selective
extraction of (bio)molecules. Separation and Purification Technology 2014;135:259-267.
[10] Ramos A, Acien FG, Fernandez-Sevilla JM, Gonzalez CV, Bermejo R. Development of a process for
large-scale purification of C-phycocyanin from Synechocystis aquatilis using expanded bed
adsorption chromatography. Journal of chromatography B, Analytical technologies in the
biomedical and life sciences 2011;879:511-519.
[11] Boeris V, Balce I, Vennapusa RR, Arevalo Rodriguez M, Pico G, Lahore MF. Production, recovery
and purification of a recombinant beta-galactosidase by expanded bed anion exchange adsorption.
Journal of chromatography B, Analytical technologies in the biomedical and life sciences
2012;900:32-37.
[12] Asgari S, Jahanshahi M, Rahimpour A. Cost-effective nanoporous Agar-Agar polymer/Nickel
powder composite particle for effective bio-products adsorption by expanded bed
chromatography. Journal of chromatography A 2014;1361:191-202.
[13] Asghari F, Jahanshahi M, Ghoreyshi AA. Preparation and characterization of agarose-nickel
nanoporous composite particles customized for liquid expanded bed adsorption. Journal of
chromatography A 2012;1242:35-42.
[14] Rezvani A, Jahanshahi M, Najafpour GD. Characterization and evaluation of the novel agarose–
nickel composite matrix for possible use in expanded bed adsorption of bio-products. Journal of
Chromatography A 2014;1331:61-68.
Apêndice 97
Nathália Kelly de Araújo Programa de Pós-Graduação em Biotecnologia/RENORBIO
[15] Yun J, Lin DQ, Yao SJ. Predictive modeling of protein adsorption along the bed height by taking
into account the axial nonuniform liquid dispersion and particle classification in expanded beds.
Journal of chromatography A 2005;1095:16-26.
[16] Li W, Zhang S, Sun Y. Modeling of the linear-gradient dye-ligand affinity chromatography with a
binary adsorption isotherm. Biochemical Engineering Journal 2004;22:63-70.
[17] Osberghaus A, Hepbildikler S, Nath S, Haindl M, von Lieres E, Hubbuch J. Optimizing a
chromatographic three component separation: a comparison of mechanistic and empiric modeling
approaches. Journal of chromatography A 2012;1237:86-95.
[18] Dismer F, Hansen S, Oelmeier SA, Hubbuch J. Accurate retention time determination of co-eluting
proteins in analytical chromatography by means of spectral data. Biotechnology and
Bioengineering 2013;110:683-693.
[19] Osberghaus A, Hepbildikler S, Nath S, Haindl M, von Lieres E, Hubbuch J. Determination of
parameters for the steric mass action model--a comparison between two approaches. Journal of
chromatography A 2012;1233:54-65.
[20] Antia FD, Horváth C. Gradient elution in non-linear preparative liquid chromatography. Journal of
Chromatography A 1989;484:1-27.
[21] Chen J, Sun Y. Modeling of the salt effects on hydrophobic adsorption equilibrium of protein.
Journal of chromatography A 2003;992:29-40.
[22] Miller GL. Use of Dinitrosalicylic Acid Reagent for Determination of Reducing Sugar. Analytical
chemistry 1959;31:426-428.
[23] Li P, Xiu G, Rodrigues AE. Experimental and Modeling Study of Protein Adsorption in Expanded
Bed. AIChE Journal 2005;51:2965-2977.
[24] Chen W-D, Dong X-Y, Bai S, Sun Y. Dependence of pore diffusivity of protein on adsorption
density in anion-exchange adsorbent. Biochemical Engineering Journal 2003;14:45-50.
[25] Tong X-D, Xue B, Sun Y. Modeling of expanded-bed protein adsorption by taking into account the
axial particle size distribution. Biochemical Engineering Journal 2003;16:265-272.
[26] Davis ME. Numerical Methods and Modeling for Chemical Engineers. New York: Wiley;1984.
[27] Petzold LR. DASSL code, version 1989, Computing and Mathematics Research Division, Lawrence
Livermore National Laboratory, L316, PO Box 808, Livermore, CA 94559;1989..
[28] Schwaab M, Biscaia JEC, Monteiro JL, Pinto JC. Nonlinear parameter estimation through particle
swarm optimization. Chemical Engineering Science 2008;63:1542-1552.
[29] Burkert CAV, Barbosa GNO, Mazutti MA, Maugeri F. Mathematical modeling and experimental
breakthrough curves of cephalosporin C adsorption in a fixed-bed column. Process Biochemistry
2011;46:1270-1277.
[30] Giordano PC, Beccaria AJ, Goicoechea HC, Olivieri AC. Optimization of the hydrolysis of
lignocellulosic residues by using radial basis functions modeling and particle swarm optimization.
Biochemical Engineering Journal 2013;80:1-9.
[31] Brun R, Reichert P, Künsch HR. Practical identifiability analysis of large environmental simulation
models. Water Resources Research 2001;37:1015-1030.
[32] Prunescu RM, Sin G. Dynamic modeling and validation of a lignocellulosic enzymatic hydrolysis
process – A demonstration scale study. Bioresource technology 2013;150:393-403.
top related