mi0023 contact tester cc rev02 - terexritz.com.br · produtos fornecidos ao cliente, peças...
TRANSCRIPT
CONTACT TESTERCC
IMPORTANTENÃO OPERE O INSTRUMENTO ATÉ QUE VOCÊ TENHA:
- ESTUDADO E ENTENDIDO COMPLETAMENTE ESTE MANUAL.
IMPORTANTDO NOT OPERATE THE INSTRUMENT UNTIL YOU HAVE:
- UNDERSTOOD THIS OWNER´S GUIDE.
MI0023-rev02
TEREX2 MI0023-rev02
SUMÁRIO INDEXProprietários, Usuários Owners, Users and Operators . . . . . 13e Operadores . . . . . . . . . . . . . . . . . . 03
Technical Assistance . . . . . . . . . . . . 13Assistência Técnica . . . . . . . . . . . . . 03
Limited Standard Guarantee of Garantia Padrão Limitada New Product. . . . . . . . . . . . . . . . . . . 14Produto Novo . . . . . . . . . . . . . . . . . . 04
1. Introduction . . . . . . . . . . . . . . . . 18
2. Safety Recommendations . . . . . . 18
3. Technical Features . . . . . . . . . . . 18
4. Panel Description . . . . . . . . . . . . 19
5. Identification . . . . . . . . . . . . . . . . 19
6. Function Test
6.1. Electronic system test . . . . . 20
6.2. Continuity test . . . . . . . . . . . 20
7. Use Preparation . . . . . . . . . . . . . 21
8. Work Instructions . . . . . . . . . . . . 21
9. Battery Change . . . . . . . . . . . . . 22
1. Introdução . . . . . . . . . . . . . . . . . 08
4.
8. Instruções de trabalho . . . . . . . . 11
9. Troca da Bateria . . . . . . . . . . . . . 12
2. Recomendações de segurança. . 08
3. Características técnicas . . . . . . . 08
Descrição do Painel . . . . . . . . . . 09
Identificação . . . . . . . . . . . . . . . . 09
6. Teste de Funcionamento
6.1. Teste do sistema eletrônico . 10
6.2.Teste de continuidade . . . . . . 10
7. Preparação para Uso . . . . . . . . . 11
5.
PO
RT
UG
UÊ
S
TEREX 3MI0023-rev02
Obrigado por escolher nosso Este manual é fornecido com seu instrumento Contact Tester CC de instrumento para familiarizar você com
®fabricação Terex para sua aplicação. seu funcionamento e fornecer as
informações de operação necessárias. Segurança é nossa prioridade número
A eficiência, performance e vida útil do um e a melhor maneira para
instrumento dependem do cuidado que alcançarmos esse objetivo é unirmos
ele recebe. Todo operador deve estar nossos esforços.
completamente familiarizado com os Cada um possui responsabilidade direta
procedimentos de operação e em busca da segurança. Para tanto,
conservação do instrumento.cada um contribuirá de forma
contundente se:NOTA
1. Cumprir todas as normas e Este manual deve ser considerado procedimentos, sejam federais, como parte de seu instrumento e estaduais, locais e da própria
deve permanecer com o mesmo companhia.
durante todo o tempo.2. Ler, entender e seguir as
instruções contidas neste manual A Terex reserva-se o direito de fazer
e outros manuais fornecidos com alterações técnicas sem dar notificação.
este equipamento. É proibida a reprodução parcial ou total.
PROPRIETÁRIOS, USUÁRIOS E OPERADORES
ASSISTÊNCIA TÉCNICASe você tiver alguma dúvida, necessitar
de maiores informações ou orientações
que não estejam contidas no manual,
entre em contato com a Assistência
Técnica da Terex (0800 031 0100).
fabrica do Vendedor, ou em outro local GARANTIA LIMITADA DO
designado pelo Vendedor, para PRODUTO FABRICADO PELA inspeção e, se o Comprador não puder EMPRESA (REV.D)confirmar que as condições (1) (i) e (1)
A TEREX BETIM EQUIPAMENTOS (ii) acima foram cumpridos, então esta
LTDA ("Vendedor"), para o produto garantia não cobrirá o defeito alegado.
fabricado pela empresa, garante que o A obrigação e responsabilidade do produto novo e as peças que fabrica e Vendedor sob esta garantia é vende em todo o mundo estão expressamente limitada, a critério COBERTOS POR GARANTIA sob exclusivo do vendedor, o fornecimento condições normais de uso e serviço, de de peças de reposição e componentes quaisquer defeitos de fabricação ou para qualquer parte que apareça ao material por um período de 12 meses Vendedor, após a inspeção, ser relativa a partir da data de entrega ao usuário a defeito de material ou mão de obra final em primeiro lugar, mas em nenhum após a devida inspeção do vendedor. caso mais de 18 meses a partir da data As peças serão fornecidas sem custo de envio da fábrica; desde que (1) O para o comprador e disponibilizadas na vendedor receba uma notificação por fábrica ou outro local do vendedor na escrito do defeito dentro de 30 (trinta) condição CIF-Pago, ou seja, o frete dias após a sua descoberta e o será pago pelo Vendedor. Todos os Comprador garanta que (i) o componentes e peças substituídas nos equipamento foi mantido e operado termos desta garantia se tornam dentro dos limites de uso nominal e propriedade do Vendedor. Deste modo, normal, e (ii) o defeito não é resultado o Comprador deve enviar as peças (por de qualquer forma de ação intencional meio de uma transportadora autorizada) ou negligência ou omissão do ao local designado conforme solicitado comprador, seus agentes ou pelo Vendedor. O frete neste caso funcionários, e (2) o registro do produto também será pago pelo Vendedor. para o produto novo foi concluída e
recebida pelo Vendedor no prazo de Esta garantia será nula e sem efeito se
trinta (30) dias da data da colocação do houver alterações não expressamente
produto "em serviço". Se solicitado pelo autorizadas pelo Vendedor, seja na
Vendedor, o Comprador deverá estrutura, partes ou componentes.
devolver o produto com defeito para
PO
RT
UG
UÊ
S
TEREX4 MI0023-rev02
GARANTIA PADRÃO LIMITADA PRODUTO NOVO
Acessórios, conjuntos e componentes Manutenção inadequada, uso indevido,
abuso, armazenamento inadequado, incluídos no produto do Vendedor, que operação além da capacidade nominal, não são fabricados pelo Vendedor, operação após a descoberta de peças estão sujeitos à garantia de seus defeituosas ou gastas, sabotagem, respectivos fabricantes. Partes normais acidente, alterações ou reparo do de manutenção, ajustes, manutenção ou produto por pessoas não autorizadas
/ desgaste, não são abrangidos por esta pelo Vendedor anulam esta garantia e a
garantia e a sua manutenção são de tornam sem efeito. Vendedor reserva-se
responsabilidade exclusiva do o direito de inspecionar a instalação do
Comprador.produto e procedimentos de
O VENDEDOR NÃO FAZ NENHUMA manutenção de revisão para determinar
se a falha é coberta por esta garantia.OUTRA GARANTIA EXPRESSA OU
IMPLÍCITA, E NÃO FAZ NENHUMA Garantia de Peças: O Vendedor garante GARANTIA DE COMERCIALIZAÇÃO que as peças fornecidas em garantia OU ADEQUAÇÃO PARA UM estão cobertas quanto aos defeitos de DETERMINADO FIM, COMO AO materiais ou mão de obra para (1) um
PRODUTO E PEÇAS QUE FORNECE. período de 12 meses após a data de
expedição da fábrica, ou (2) o saldo Nenhum funcionário ou representante restante da garantia do produto novo, o
do Vendedor está autorizado a modificar que ocorrer primeiro. Em relação às
esta garantia, a menos que tal peças encomendadas ao Vendedor para
modificação seja feita por escrito e produtos para os quais a garantia
assinada por um representante expirou, o Vendedor garante que essas autorizado do Vendedor. Garantia do partes são livres de defeitos de Vendedor é contínua para o período materiais ou mão de obra por um indicado, e "parar e reiniciar", tal prazo período de 90 dias após a data de não é permitido. expedição da fábrica.
A obrigação do Vendedor sob esta NÃO TRANSFERÊNCIA DE garantia não incluem encargos, GARANTIA: A garantia é limitada ao
impostos, taxas ambientais, incluindo Comprador original ou usuário final
original. Não é transferível ou não são sem limitação, alienação ou transferíveis sem a aprovação formal e manipulação de pneus, baterias, itens por escrito do Vendedor.petroquímicos, ou quaisquer outros
encargos. Vendedor não será ITENS não cobertos pela garantiaresponsável por danos indiretos,
Os itens seguintes, os quais não se incidentais ou consequentes, mesmo exaurem nesta lista, não são cobertos avisado da possibilidade de tais danos. por esta garantia:
PO
RT
UG
UÊ
S
TEREX 5MI0023-rev02
1. Itens vendidos por qualquer de serviços, inspeções, tempo de
indivíduo, empresa, sociedade ou diagnóstico, tempo de viagem e
qualquer outra organização ou pessoa suprimentos, tais como limpeza de mão,
jurídica não autorizado pelo Vendedor toalhas e lubrificantes.
para distribuir o seu produto. 6. Danos causados por transportadora.
2. Frete de entrada, impostos e taxas Qualquer reclamação por danos devem
para os componentes de substituição ser formalizada imediatamente com a
ou de carga de saída, encargos e respectiva transportadora.
impostos para qualquer peça solicitada 7. Reparações, trabalhos exigidos ou como um retorno de garantia. partes expostas como resultado do
3. Componentes que não são tempo de uso, armazenamento,
fabricados pelo Vendedor ou suas intempéries, a falta de utilização,
afiliadas. Tais componentes podem demonstração, ou uso para o transporte
incluir, mas não estão limitados a, de produtos químicos corrosivos.
chassis, motores, baterias, pneus, 8. Danos resultantes no produto ou produtos fornecidos ao cliente, peças causados pelo operador ou transmissões, compressores de ar, e os proprietário após notarem que ocorreu eixos. algum tipo de falha no equipamento.
4. Substituição de um conjunto 9. Danos causados por trabalho completo que é reparável em campo realizado por pessoal não autorizado pela substituição ou reparo da peça pelo Vendedor para conserto do defeituosa (s) dentro do conjunto. produto.
O Vendedor tem a opção de reparar ou 10. Viagens e despesas relacionadas, substituir qualquer peça defeituosa ou para uma área geográfica onde o conjunto. Vendedor não tem presença de serviços
5. Peças de uso e desgaste e serviços estabelecido ou fretes relacionados à
de manutenção, incluindo, mas não expedição do Comprador de
limitados a: lâmpadas, lentes, equipamentos para um local aprovado
retentores, juntas, mangueiras, filtros, para reparo.
respiros, cintos, bicos, placas de EM NENHUM CASO O VENDEDOR fricção da embreagem, forros, vidro e OU QUALQUER DE SUAS freio, cabos, porcas e fixadores, SUBSIDIÁRIAS OU DIVISÕES revestimentos exteriores, aperto dos FICARÁ RESPONSÁVEL POR parafusos, adição ou substituição de PERDAS OU DANOS ACIDENTAIS, fluidos, os ajustes de qualquer natureza, CONSEQUENTES E OUTROS
PO
RT
UG
UÊ
S
TEREX6 MI0023-rev02
RESULTANTES DE UMA INFRAÇÃO A responsabilidade do Vendedor para o
DA GARANTIA, REPRESENTAÇÃO Comprador não deve, em qualquer
OU CONDIÇÃO, EXPRESSA OU situação, exceder o preço de compra
IMPLÍCITA, OU QUAISQUER do produto.
TERMOS DESTA GARANTIA, OU ESTA GARANTIA CANCELA E QUALQUER INFRAÇÃO DE SUBSTITUI TODAS AS DEMAIS QUALQUER DEVER OU OBRIGAÇÃO GARANTIAS, REPRESENTAÇÕES E IMPOSTA POR ESTATUTO, CONDIÇÕES, EXPRESSAS OU CONTRATO, OBRIGAÇÕES IMPLICITAS E TODAS AS OUTRAS RELATIVAS A DANOS E DE DIREITO OBRIGAÇÕES ESTATUTÁRIAS, CONSUETUDINÁRIO OU QUALQUER CONTRATUAIS, OBRIGAÇÕES OUTRA (CAUSADAS OU NÃO RELATIVAS A DANOS E DE DIREITO CAUSADAS POR NEGLIGÊNCIA DO CONSUETUDINÁRIO OU VENDEDOR, SEUS EMPREGADOS, RESPONSABILIDADES SOBRE O AGENTES E QUALQUER OUTRO VENDEDOR SÃO EXPRESSAMENTE CORRELATO), INCLUINDO, SEM EXCLUIDAS NA MAXIMA EXTENSÃO LIMITAÇÃO, PERDA DE USO, PERDA PERMITIDA POR LEI. NÃO EXISTE DE LUCROS OU RECEITAS, GARANTIA QUE SE EXTENDA ALÉM CUSTOS DE MAO DE OBRA E DA GARANTIA CONTIDA NESTE TRABALHO, PRIVAÇÃO DO USO DE DOCUMENTO. OUTROS EQUIPAMENTOS, TEMPO
O Vendedor não assume nem autoriza DE INATIVIDADE OU ENCARGOS
qualquer outra pessoa a assumir pelo COM CONTRATAÇÃO, CONSERTO
Vendedor qualquer outra DE TERCEIROS, DESEMPENHO OU
responsabilidade em conexão com a TRABALHO IMPRÓPRIO, PERDA DE
venda do produto do Vendedor. No SERVIÇO DE PESSOAL, PERDA DE
caso de qualquer disposição desta OPORTUNIDADE PRESTADORA DE
garantia se tornar inexequível por SERVIÇO E PENALIDADES DE
qualquer razão, as disposições QUALQUER NATUREZA, LESÃO
permanecerão em pleno vigor e efeito.CORPORAL, ABALO MENTAL OU
EMOCIONAL OU FALHA DO
EQUIPAMENTO EM RESPEITAR
QUALQUER LEI APLICÁVEL.
PO
RT
UG
UÊ
S
TEREX 7MI0023-rev02
PO
RT
UG
UÊ
S
TEREX8 MI0023-rev02
O Contact Tester CC é um instrumento Este instrumento detecta tensão de
detector de tensão por contato com o polaridade positiva, não podendo
condutor em redes de corrente portanto, ser utilizado para detectar a
continua. polaridade negativa da rede.
1. INTRODUÇÃO
- Evite pancadas ou quedas, pois - Remova a bateria se o instrumento
podem danificar o instrumento; não for utilizado por um longo período
de tempo (15 dias). Este - Verifique o estado de carga da bateria procedimento evita a descarga e a de acordo com o item 6.1;corrosão da bateria;
- Teste o perfeito funcionamento do - Jamais substitua qualquer peça ou CC antes e depois de
altere qualquer ajuste do instrumento;seu uso (ver item 6);
- Qualquer manutenção deverá ser - Sempre que o CC feita pelo fabricante.não estiver sendo utilizado, mantenha-
o acondicionado em seu estojo, em
local fresco e seco;
Contact Tester
Contact Tester
2. RECOMENDAÇÕES DE SEGURANÇA
- Sistema de detecção por contato - Consumo máximo em operação de
324 mW;direto com o condutor, através de
eletrodo de contato; - Temperatura de trabalho entre -5 °C
e 70 °C;- Sinais de indicação sonoros e
luminosos; - Pressão sonora 80 dB +- 5% a 1m
de distância;- Teste de funcionamento e de carga - Força máxima de aperto do eletrodo da bateria incorporado ao sistema;
de 10 N/m;- Alimentação através de bateria
- Peso sem acondicionamento e alcalina 9 V modelo 6LR61;extensão: 1,08 kg;
3. CARACTERÍSTICAS TÉCNICAS
PO
RT
UG
UÊ
S
TEREX 9MI0023-rev02
- Comprimento sem extensão: 80 mm;
- Diâmetro de aproximadamente 60 mm;
- Comprimento do cabo de
aterramento: 10 m;
- Design circular que permite ao
operador uma melhor visualização do
ponto a ser testado;
- Próprio para uso em meio interno Figura 1 - Contact Tester CC
e externo.
1 - Led Piloto (P)
2 - Chave Seletora (L/AT; D; T)
3 - Led's de sinalização (S)
4 - Led de continuidade (C)
5 - Alarme sonoro
Figura 2 - Painel frontal do Contact Tester CC
4. DESCRIÇÃO DO PAINEL
1
23
4
5
A identificação do Contact Tester CC é Referencia - Número de referencia no
feita através da etiqueta da figura 3. catálogo Terex;
Nº de serie - Número de série do
equipamento;
Faixa de tensão - Faixa de tensão na
qual o equipamento pode operar;
Data - Data de produção do
Figura 3 - Etiqueta de identificação equipamento;
5. IDENTIFICAÇÃO
PO
RT
UG
UÊ
S
TEREX10 MI0023-rev02
Alimentação - Tipo de fonte de
alimentação utilizada pelo instrumento.
OBS.: O modelo de Contact Tester CC
e sua respectiva faixa de tensão pode
ser visualizado na tabela 1:Tabela 1- Referencia de catalogo Terex
InstrumentoFaixas de
Tensão
Classe
de
Tensão
CT-CC 0,5-5 500 V - 5 kV Média
Permite verificar o perfeito - Os Led's de Sinalização e o alarme
funcionamento do sistema eletrônico, Sonoro serão acionados duas vezes
Led's de Sinalização, alarme Sonoro e indicando que o instrumento está
carga da bateria. O teste de operando corretamente;
funcionamento deve ser feito antes e - Retorne a chave para posição de depois do uso do instrumento. “Desligado”.
- Coloque a chave seletora na posição OBS.: O Led Piloto deverá permanecer “L/AT”; acesso durante o teste e durante o uso
- O Led Piloto acenderá indicando que do instrumento. Caso ele não acenda,
a bateria está com carga; pisque aleatoriamente ou apague,
substitua a bateria (ver item 9).
6. TESTE DE FUNCIONAMENTO
6.1. TESTE DO SISTEMA ELETRÔNICO
Este teste verifica a continuidade
elétrica e as conexões do sistema de
detecção.
- Conecte o cabo de aterramento ao
conector do instrumento;
- Conecte a garra de aterramento do Figura 4 - Ligação do cabo de aterramentocabo em uma estrutura ou trilho;
OBS.: caso o Led de continuidade não - Posicione a chave seletora na
ascenda, verifique todas as conexões e posição “T”;
execute o teste novamente. O - Toque um ponto da estrutura aterrada instrumento só poderá ser utilizado se com o eletrodo de contato;for aprovado no teste de continuidade.- O Led de continuidade deve ascender;
6.2. TESTE DE CONTINUIDADE
PO
RT
UG
UÊ
S
TEREX 11MI0023-rev02
- Atente-se para os valores de tensão
de operação do instrumento;
- Certifique-se de que o eletrodo de
contato esteja rosqueado e aperte-o
se necessário;
- Conecte o Contact Tester CC à Vara
de manobra, utilizando o adaptador
Universal;
- Conecte o cabo de aterramento ao
conector do instrumento;
- Verifique o comprimento adequado
do elemento isolante considerando a
distância de segurança de acordo
com a tabela 2.
As distancias de segurança
recomendadas nessa tabela estão de
acordo com a publicação da OSHA -
Occupational Safety Health
Administration EUA - Administração
Ocupacional de Segurança e Saúde. Tabela 2 - Recomendações das distancias de segurança
7. PREPARAÇÃO PARA USO
Tensão
Nominal
(kV)
Distância
fase-terra
(m)
Distância
fase-fase
(m)
0,05 a 1,0 Evite Contato Evite Contato
1,1 a 15 0,64 0,66
15,1 a 36 0,72 0,77
36,1 a 46 0,77 0,85
46,1 a 72,5 0,90 1,05
72,6 a 121 0,95 1,29
138 a 145 1,09 1,50
161 a 169 1,22 1,71
230 a 242 1,59 2,27
245 a 326 2,59 3,80
500 a 550 3,42 5,50
765 a 800 4,53 7,91
- Atente-se sempre para as normas de - Coloque a chave seletora na posição
“L/AT”. O Led Piloto deverá segurança de sua empresa,
permanecer aceso durante toda a Ministério do Trabalho ou outras operação;instituições e verifique as condições
do local de trabalho onde o Contact - Conecte o cabo de aterramento ao
Tester CC será utilizado; terra do sistema a ser medido;
- Execute o teste de funcionamento - Eleve o CONTACT TESTER CC e
conforme item 6; toque o condutor a ser testado com o
eletrodo de contato.
8. INSTRUÇÕES DE TRABALHO
TEREX12 MI0023-rev02
PO
RT
UG
UÊ
S
- Atentar para o seguinte modo de - Executar novamente o teste de
funcionamento: funcionamento conforme item 6 para
assegurar-se de que o instrumento I. Se o condutor estiver ENERGIZADO, está funcionando corretamente.o equipamento emitirá sinais
luminosos e sonoros, de forma CUIDADO: Mesmo que o condutor
intermitente; esteja desenergizado, poderá haver
tensões induzidas por outros circuitos, II. Se o condutor estiver ou tensões capacitivas provenientes dos DESENERGIZADO, o equipamento outros condutores do mesmo circuito. NÃO EMITIRÁ nenhum tipo de sinal.Portanto, antes de tocar qualquer
- Ao recolher o Contact Tester CC, condutor com as mãos, deve-se realizar
evite bater o instrumento contra o aterramento do mesmo.
solo;
Retire o parafuso de fixação e remova a
parte interna do instrumento.
A bateria esta localizada em um Figura 5 - localização da bateria
compartimento abaixo do encaixe do
eletrodo de contato.
9. TROCA DA BATERIA
EN
GLIS
H
TEREX 13MI0023-rev02
Thank you for choosing our Contact The efficiency, performance and life Tester CC, made by Terex® for your cycle of the instrument depend on application. maintenance quality. Every operator
should be fully familiar with all Safety is our top priority and the best way to reach that goal is joining our operational and upkeep of the efforts. Everyone is directly responsible instrument.in the search for a safe operation. To that extent, everyone's contribution will NOTE be decisive if:
This manual should be considered 1. You comply with all federal, state, as part of your instrument and
local and company's procedures should remain with the same all
and rulesthe time.
2. Read, understand and follow the
instructions contained in this Terex reserves the right to make
guide technical changes without prior
notifications.This manual is supplied with your
instrument, so you may get familiar with It is forbidden the full or partial copy of this Owner´s guide. how it works and also to provide the
information on how to operate it.
OWNERS, USERS AND OPERATORS
TECHNICAL ASSISTANCE In case you have any questions or need any further information or guidance not contained in this guide, please, contact Terex Technical Assistance team (0800 031 0100).
EN
GLIS
H
TEREX14 MI0023-rev02
The obligation and Seller's liability under LIMITED WARRANTY OF
this warranty is expressly limited, at the MANUFACTURED BY PRODUCT sole discretion of the seller, the supply NOW (REV.D)of spare parts and components for any
TEREX BETIM EQUIPMENT LTDA party that appears to Seller upon
("Seller") for the product manufactured by inspection, be related to defects in
the company, ensures that the new material or workmanship after proper
product and parts that manufactures and inspection of the seller. The parts will be
sells worldwide are COVERED BY provided without cost to the purchaser
WARRANTY under normal use and and made available at the factory or
service, from defects in workmanship or other location of the seller in the CIF-
material for a period of 12 months from paid condition, that is, the freight will be
the date of delivery to the end user first, paid by the seller. All components and
but in no case more than 18 months from parts replaced under this warranty
the factory shipping date; provided that become the property of the seller. Thus,
(1) Seller receives written notice of the the Purchaser shall send the parts
defect within thirty (30) days after its (through an authorized carrier) to the
discovery and Buyer guarantees that (i) appointed place as requested by the
the equipment is maintained and operated Seller. The freight in this case will also
within the limits of rated and normal use, be paid by Seller.
and ( ii) the defect is not the result of any This warranty will be null and void if form of intentional action or negligence or there are changes not expressly omission of the purchaser, its agents or approved by the Seller, in the structure, employees, and (2) product registration parts or components.for the new product was completed and
received by the Seller within thirty (30) Accessories, sets and components
days from the date of product placement included in the Seller's product, which
"in service". If requested by Seller, Buyer are not manufactured by Seller, are
shall return the defective product to subject to the warranty of their
Seller's factory, or other location respective manufacturers. Normal
designated by Seller, for inspection and, if maintenance parts, adjustments,
the Buyer can not confirm that the maintenance or / wear are not covered
conditions (1) (i) and (1) ( ii) above have by this warranty and maintenance are
been met, then this warranty does not the sole responsibility of the Buyer.
cover the alleged defect.
STANDARD LIMITED WARRANTY NEW PRODUCT
EN
GLIS
H
SELLER MAKES NO OTHER Parts Warranty: Seller warrants that the
WARRANTY EXPRESS OR IMPLIED, supplied parts are covered under
AND MAKES NO WARRANTY OF warranty as to defects in materials or
MERCHANTABILITY OR FITNESS workmanship for (1) a period of 12
FOR A PARTICULAR PURPOSE, AS months after the factory shipping date,
TO THE PRODUCT AND PARTS or (2) the remaining balance of the
PROVIDES. security the new product, whichever
comes first. Regarding the parts No employee or representative of Seller ordered from the Seller to products for is authorized to modify this warranty which the warranty has expired, the unless such modification is in writing Seller warrants that these parts are free and signed by an authorized from defects in materials or representative of Seller. Seller's workmanship for a period of 90 days warranty is continuous for the period after the date of shipment from the indicated, and "stop and restart", such factory.term is not allowed.
NO WARRANTY OF TRANSFER: The Seller's obligation under this warranty guarantee is limited to the original does not include charges, taxes, Purchaser or original end user. It is not environmental taxes, including without transferable or non-transferable without limitation, disposal or handling of tires, the formal written approval of the Seller.batteries, petrochemical items, or any
other charges. Seller shall not be liable ITEMS not covered
for any indirect, incidental or The following items, which do not consequential damages, even if advised exhaust this list, are not covered by this of the possibility of such damages. warranty:
Improper maintenance, misuse, abuse, 1. Items sold by any individual, firm, improper storage, operation beyond company or any other organization or rated capacity, operation after discovery entity not authorized by Seller to of defective or worn parts, sabotage, distribute your product.accident, alteration or repair of the
2. Input freight, taxes and fees for Product by persons not authorized by
replacement components or outbound Seller cancel the warranty and make it
freight, charges and taxes for any part void . Seller reserves the right to inspect
requested as a warranty return.the installation of the product and review
3. Components that are not maintenance procedures to determine if
manufactured by Seller or its affiliates. the failure is covered by this warranty.
TEREX 15MI0023-rev02
TEREX16 MI0023-rev02
Such components may include, but are 9. Damage caused by work undertaken
not limited to, frames, motors, batteries, by personnel not authorized by Seller to
tires, customer supplied products, service the product.
transmissions, air compressors, and 10. Travel and related expenses, to a shafts. geographical area where the seller has
4. Replacement of a complete set which no presence services established or
is repairable in the field to replace or related to freight shipping the equipment
repair the defective part (s) inside the Buyer to an approved location for repair.
assembly. IN NO EVENT SHALL SELLER OR
The seller has the option to repair or ANY OF ITS SUBSIDIARIES OR
replace any defective part or assembly. DIVISIONS WILL BE LIABLE FOR
LOSSES OR INCIDENTAL, 5. Parts of wear and tear and CONSEQUENTIAL AND OTHER maintenance services, including but not RESULT OF A BREACH OF limited to: light bulbs, lenses, seals, WARRANTY, REPRESENTATION OR gaskets, hoses, filters, vents, belts, CONDITION, EXPRESS OR IMPLIED, rings, clutch friction plates, ceilings, OR ANY TERMS OF THIS glass and brake cables , nuts and WARRANTY, OR ANY fasteners, exterior coatings, tightening INFRINGEMENT OF ANY DUTY OR of screws, addition or replacement of OBLIGATION IMPOSED BY STATUTE, fluids, adjustments of any kind, services, CONTRACT OBLIGATIONS inspections, diagnostic time, travel time RELATING TO DAMAGE AND and supplies such as hand cleaners, COMMON LAW OR OTHERWISE towels and lubricants.(CAUSED OR NOT CAUSED BY
6. Damage caused by carrier. Any claim SELLER'S NEGLIGENCE, ITS
for damages must be formalized EMPLOYEES, AGENTS AND ANY
immediately with the respective carrier.OTHER correlate) INCLUDING,
7. Repairs, work required or parts WITHOUT LIMITATION, LOSS OF
exposed as a result of using time, USE, LOST PROFITS OR REVENUES,
storage, weather, lack of use, COSTS OF WORK OF MAO AND
demonstration, or used to transport WORK, USE THE LOSS OF OTHER
corrosive chemicals. EQUIPMENT, DOWNTIME OR
CHARGES WITH CONTRACTING, 8. Damage resulting in the product or THIRD PARTY SERVICE, parts caused by the operator or owner PERFORMANCE OR IMPROPER after noticing that occurred some kind of WORK, PERSONAL SERVICE LOSS equipment failure.
EN
GLIS
H
TEREX 17MI0023-rev02
OF OPPORTUNITY PROVIDER LOSS DAMAGE AND customary law OR
OF SERVICE AND PENALTIES OF LIABILITIES ON THE SELLER ARE
ANY KIND, PERSONAL INJURY, EXPRESSLY EXCLUDED THE
EMOTIONAL OR MENTAL ABALO OR MAXIMUM EXTENT PERMITTED BY
FAILURE OF EQUIPMENT IN LAW. THERE IS NO WARRANTY
RESPECT ANY APPLICABLE LAW. THAT EXTEND BEYOND THE
WARRANTY CONTAINED HEREIN.The Seller's liability to Buyer shall not in
any event exceed the purchase price of Seller neither assumes nor authorizes
the product. any other person to assume the seller
any other liability in connection with the CANCEL THIS WARRANTY AND IN sale of the seller of the product. In the LIEU OF ALL OTHER WARRANTIES, event that any provision of this warranty REPRESENTATIONS AND become unenforceable for any reason, CONDITIONS, EXPRESS OR IMPLIED the provisions shall remain in full force AND ALL OTHER LIABILITIES and effect.STATUTORY, CONTRACT,
OBLIGATIONS RELATING TO
EN
GLIS
H
TEREX18 MI0023-rev02
Contact Tester CC is a instrument, This instrument detects positive polarity
voltage detector by contact with voltage and can not therefore be used
conductor in continuum current to detect the negative polarity of the
network. network.
1. INTRODUCTION
- Avoid impact or falls, as it could - Remove battery if the instrument is
damage the equipment; not used for a long period of time (15
days). This procedure avoids battery - Check battery charge status discharge and corrosion;according to item 6.1;
- Never replace any parts or change - Test perfect functioning of the any adjustment of the instrument;Contact Tester CC before and after
its use (see item 6); - Any maintenance should be
performed by manufacturer.- Whenever the Contact Tester CC is
not being used, keep it in its case, in
a fresh and dry place;
2. SAFETY RECOMMENDATIONS
- Detection System by direct contact - Work temperature between -5°C and
with conductor via electrode of 70°C;
contact;- Sound pressure 80 dB ± 5% to 1m
- Luminous and sound indication signs; distance;
- Functioning and battery charge test - Maximum strength of electrode incorporated to system; tightening of 10 N/m;
- Power Fed via 9V alkaline battery - Weight without case and extension:
6LR61 model;1,08Kg;
- Maximum consumption in 324 mW
operation;
3. TECHNICAL FEATURES
EN
GLIS
H
TEREX 19MI0023-rev02
EN
GLIS
H
- Length without extension: 80 mm;
- Diameter approximately 60 mm;
- Grounding cable length: 10 m;
- Circular design which allows better
viewing to the operator of the point to
be tested;
- Suitable for internal and external use.
Image 1 - Contact Tester CC
1 - Led Pilot (P)
2 - Selector Switch (L/AT; D; T)
3 - Signal LEDs (S)
4 - Led of continuity
5 - Sound alarm
Image 2 - Front panel of Contact Tester CC
4. PANEL DESCRIPTION
1
23
4
5
Contact Tester CC identification is Cat. No. - Reference number on Terex
made via image 3 tag. catalog;
Serial No. - Series number of equipment;
Voltage Range - Tension rate in which
equipment can operate;
Date - Production date of equipment;
Image 3 - Identification tag
5. IDENTIFICATION
Power Source - Type of power source
feeding used by instrument
NOTE: Contact Tester CC model and
its respective voltage rates could be
viewed on table 1:Table 1 - Reference of Terex catalog
Allows checking for perfect functioning - The signal LEDs and the sound alarm
of the electronic system, signal LEDs, will be activated in a synchronized
sound alarm and battery charge. The and interrupted way, indicating the
functioning test should be made before instrument is correctly operated;
and after instrument use. - Turn switch to “Off” position.
- Put selector switch on “L/AT” NOTE: The Pilot Led should remain on position; during test and instrument use. In case it
- The Pilot Led will turn on indicating is not on, remains intermittent or switches
battery is charged; off, replace battery (see item 9).
6. FUNCTION TEST
6.1. ELECTRONIC SYSTEM TEST
This test verifies electrical continuity and
detection system connections.
- Connect grounding cable to
instrument connector;
- Connect a cable claw grounding in a
structure or trail; Image 4 - Connection of grounding cable
- Position selector switch on “T” NOTE: In case Continuity led does not position; turn on, check all connections and
execute the test once more. Instrument - Touch a point of the grounded could be used if approved on continuity structure with contact electrode;only.
- Continuity Led should turn on.
6.2. CONTINUITY TEST
Instrument Tension Rates Tension
Class
CT-CC 0,5-5 500 V - 5 kV Medium
EN
GLIS
H
TEREX20 MI0023-rev02
- Pay attention to tension and operation
frequency values of instrument;
- Make sure that contact electrode is
screwed and fasten it, if necessary;
- Connect Contact Tester CC to
maneuver rod using universal adapter;
- Connect a cable grounding to
instrument connector;
- Check appropriate length of isolating
element considering safety distance,
according to table 2.
Safety distances recommended in this
table are according to OSHA -
Occupational Safety Health
Administration USA publications.
Table 2 - safety distance according to tension
7. USE PREPARATION
- Pay attention to safety guidance of - Connect the grounding cable to earth
your company, Ministry of Labor or of system to be tested;
other institutions and check work - Lift CONTACT TESTER CC and location conditions where Contact touch conductor to be tested with Tester CC will be used; contact electrode.
- Execute function test according to - Pay attention to following function item 6; mode:
- Put selector switch on “L/AT” I. If conductor is ENERGIZED, position. Pilot Led should remain on instrument will emit light and sound during whole operation; signs interruptedly;
8. WORK INSTRUCTIONS
Voltage
Distance
(kV)
Distance
Phase-
Ground (m)
Distance
Phase-
Phase (m)
0.05 to 1.0 Avoid contact Avoid contact
1.1 a 15 0.64 0.66
15.1 a 36 0.72 0.77
36.1 a 46 0.77 0.85
46.1 a 72.5 0.90 1.05
72.6 a 121 0.95 1.29
138 a 145 1.09 1.50
161 a 169 1.22 1.71
230 a 242 1.59 2.27
245 a 326 2.59 3.80
500 a 550 3.42 5.50
765 a 800 4.53 7.91
EN
GLIS
H
TEREX 21MI0023-rev02
II. If conductor is DE-ENERGIZED, CAUTION: Even if conductor is de-
instrument WILL NOT EMIT any type energized, induced tensions by other
of sign. circuits could occur, or capacitive
tension derived from other conductors - When retract Contact Tester CC on the same circuit. Therefore, before avoid hit instrument against the floor;touch any conductor with your hand, its
Execute one more time function test grounding should be performed.
according to item 6 to make sure the
instrument is working correctly.
Take off fastener screw from instrument
end and remove internal part of
instrument.Image 5 - Battery location
Battery is located in a compartment
under contact electrode fit.
9. BATTERY CHANGEEN
GLIS
H
TEREX22 MI0023-rev02
www.terexutilities.com.br
Data de Vigência: Agosto 2015. Especificações dos produtos estão sujeitas a alterações sem aviso prévio ou notificação. As fotografias e/ou desenhos neste documento são apenas para fins ilustrativos. Consulte as instruções apropriada para o uso correto dos equipamentos. Não seguir as instruções apropriadas ao usar o nossos produtos ou qualquer outro ato irresponsável pode resultar em ferimentos graves ou morte. Produtos e serviços mencionados podem ser marcas comerciais, marcas de serviço ou nomes comerciais da Terex
® Corporation e/ou suas subsidiárias nos EUA e outros países. Todos os direitos reservados. Terex é uma marca registrada da Terex Corporation nos EUA e em vários outros países. Copyright 2015 Terex Corporation.
Effective Date: August 2015. Product specifications are subject to change without previous notice or notification. The pictures and / or drawings herein are for illustrative purposes only. See the instructions appropriate for the proper use of equipment. Failure to follow the appropriate instructions to use our products or to otherwise act irresponsibly may result in serious injury or death. Products and services mentioned may be trademarks, service marks or trade names of Terex Corporation and / or its subsidiaries in the U.S. and other
®countries. All rights reserved. Terex is a registered trademark of Terex Corporation in the U.S. and several other countries. Copyright 2015 Terex Corporation.
Tel. + 55 31 2125 4053 | Fax + 55 31 2125 4100Rod. BR 381, km 488 | 32681-200 | Betim | MG | Brasil